Recent content by Rhialto

the newest DX8/etc drivers for win2k are excellent! during my Unreal T sessions I am averaging between 65 - 80 frames/sec consistently. Much better than the older drivers.

I have a Duron800@918, 256 MB ram, fastrack66, Radeon 32DDR, Soundblaster live Plat 5.1, a cheapo ethernet card and the latest via 4in1s. I ran into HUGE problems trying to install win98. I had to move the fastrack66 into PCI slot 1 (right under the AGP slot) and I assigned interrupts to each...

I have a Duron 800@918/Radeon 32DDR and with the new drivers I have finally pulled Win98 off my system. Win2K only. The new drivers gave me huge increases in speed on Win2K.

I am using a 800 Duron at 918 on my Pro 2a with a Radeon DDR and its rock solid. the new drivers from ATI for W2K are a god send. Q3 and UT are ENTIRELY playable now :))

I have finally reinstalled everything W2k and Win98. Had to assign IRQs but now my system seem rock solid... thank god!!

I have found W2K much easier to install and upkeep. With the new Radeon drivers QIII and UT are entirely playable. W98 has been hell on earth for me as far as installing (might have something to do with my RAID card) but I was get BSODs galore during the install. I have something reasonable...

I am getting spurious freezes as well in W2K and I am starting to suspect the mainboard. 98 is miss behaving for me (problems every other boot with windows protection faults). I am arriving at wits end (unfortunately, it was a short journey :)

I have a microsoft ps2 keyboard. I am also trying to reinstall win 98 on this box...holy cow...what a pain in the @ss. Every other boot it give me a windows protection error. I boot into 'safe mode' then reboot and everything comes up fine. I know its a 98 problem because 2000 works fine...

I have a nearly identical config: Radeon, 256 MB ram, CDRW, 120 atapi super disk, Promise66 raid controller with two drives striped, Dual boot 98, 2000 I has always had an annoying (read REALLY annoying) delay on boot up right after it detects the devices on the onboard IDE channels. I have...

I have pretty much the same setup with no errors to speak of (except the ability of my mainboard to continue to front side bus overclock.) Nothing relating to the Radeon though.

One thing that I have noticed: My Duron used to run at 9.0 x 106 on my Pro2-a (and it ran for about a week.) Then, it started to crash. I have had to keep backing the FSB back to where it will only run at 9.0 x 102 now. Not sure whats going on, but I have noticed a few other posters who have...

One thing that I have noticed: My Duron used to run at 9.0 x 106 on my Pro2-a (and it ran for about a week.) Then, it started to crash. I have had to keep backing the FSB back to where it will only run at 9.0 x 102 now. Not sure whats going on, but I have noticed a few other posters who have...

I have a mine set to auto auto. Mind you I only have my CDROM & LS120 on the onboard IDE controller. I am also running a Promise66 card that I boot from. On a warm boot sometimes it doesn't even find my drives, but a cold boot always brings them back. What do you have set for your three...

I have the MSI and its solid. Getting pretty good memory scores as well. Duron 800@963 (1.7v and 107Mhz fsb) My cooler sucks so I am pretty sure my Duron would preform solidly at 1gig with a better cooler.

The scores for my duron 800@846 (106mhz bus) in 2000 are: int: 441 fpu: 533 800@800 (100) scores are: int: 422 fpu: 505