• We’re currently investigating an issue related to the forum theme and styling that is impacting page layout and visual formatting. The problem has been identified, and we are actively working on a resolution. There is no impact to user data or functionality, this is strictly a front-end display issue. We’ll post an update once the fix has been deployed. Thanks for your patience while we get this sorted.

...UPDATE... A64 heatsink temps

M

Monoman

Platinum Member
[UPDATE] after setting up my rig in a Antec Super Lanboy with the stock HSF I am getting idle temps of 45C-49C and at the peak of my 24Hr prime95 tourchure run it got to 63C :Q is this normal or should I get a better cooling option. I have seen marks temps and in no way does mine even come close tho those. I even have to disable C&Q because it whud throttle down the fan and run at 55C idle temps. I have receated he HSF twice and both times I reapplied a very thin coat of AS5.[/UPDATE]

any advice? or just tell me to shut up! 😀


honestly, the stock works fine, I just would like to try lapping a HSF. Also, please state your reasons for answer if you would 😀
 
Why not LAP the stock one and see how it improves if it does enough then sweet saved some money, if not get something else?
 
Originally posted by: SickBeast
Since you don't have much overclocking headroom with that chip I would just stick with the stock HSF.
Click to expand...

see, Thats my opinion too, I just wanted to get a feel from the peeps here 😀
 
Do you already have the sand paper? If not you'll need to gather up an assorted mix for the job. Figure $5-$8 maybe less, then spend time polishing it with the lowest to highest grit until you got it right. My guess is that you have already read up on the process so you probably already know what you will need to have and what to do.

Or, if you just want to knock a few degrees off your temps you can skip all the foot work and just get one of these from Newegg for about $15 shipped. It's not the best cooler, but for the money it's a very popular and effective cooler for those wanting an improvement over stock. I've got one on an 1800 and the temps never go above 40C on my Shuttle.
 
Ya, if you don't plan on increasing the voltage, and don't mind the noise level of the included HSF, just lap it and enjoy.
 
Originally posted by: Texun
Do you already have the sand paper? If not you'll need to gather up an assorted mix for the job. Figure $5-$8 maybe less, then spend time polishing it with the lowest to highest grit until you got it right. My guess is that you have already read up on the process so you probably already know what you will need to have and what to do. Or, if you just want to knock a few degrees off your temps you can skip all the foot work and just get one of these from Newegg for about $15 shipped. It's not the best cooler, but for the money it's a very popular and effective cooler for those wanting an improvement over stock. I've got one on an 1800 and the temps never go above 40C on my Shuttle.
Click to expand...

so you think this HSF is better than the A63 stock cooler? from the add @ newegg it seems less effective due to the smaller amount of copper present but I am no means an expert here.



also, I do know what it take to lap but I don't have the sandpaper yet and If I do decide to go that route I will pick some up. If I do LAP I will do it tomarrow evening 😀

Thanks to all who voted so far
 
Leave it alone unless you're going to strap a Prometiea on there...
EDIT: You can also wave goodbye to your warranty if you lap the heatsink or heatspreader.
 
You would want to lap the CPU's heatspreader too. One even surface + one uneven surface does not really get you very far 😉
 
Originally posted by: mechBgon
You would want to lap the CPU's heatspreader too. One even surface + one uneven surface does not really get you very far 😉
Click to expand...

ah damn.... good idea but... when lapping don't you use water? water + proc = ???? I would be alittle concerned with that unless you can lap w/o using water and soap.
 
Or, if you just want to knock a few degrees off your temps you can skip all the foot work and just get one of these from Newegg for about $15 shipped. It's not the best cooler, but for the money it's a very popular and effective cooler for those wanting an improvement over stock. I've got one on an 1800 and the temps never go above 40C on my Shuttle
Click to expand...

That won't quite work as it doesn't fit A64's...
 
Originally posted by: JBT
Or, if you just want to knock a few degrees off your temps you can skip all the foot work and just get one of these from Newegg for about $15 shipped. It's not the best cooler, but for the money it's a very popular and effective cooler for those wanting an improvement over stock. I've got one on an 1800 and the temps never go above 40C on my Shuttle
Click to expand...

That won't quite work as it doesn't fit A64's...
Click to expand...

Oops! Your're right.... I didn't read the title correctly.
rolleye.gif
 
Originally posted by: Monoman
Originally posted by: mechBgon
You would want to lap the CPU's heatspreader too. One even surface + one uneven surface does not really get you very far 😉
Click to expand...

ah damn.... good idea but... when lapping don't you use water? water + proc = ???? I would be alittle concerned with that unless you can lap w/o using water and soap.
Click to expand...
Yeah, exactly right. I lapped Celerons back in the day and that's exactly what you do... smack 'em heatspreader-side-down on wet sandpaper and lap them. Bye-bye warranty, of course.

Remember that the goal of lapping isn't to make the surfaces smooth, it's to make them flat. That way, the layer of thermal compound can be very, very thin, allowing the thermal transfer to be improved. Personally, I would just use the stock retail heatsink as-is unless it's too noisy, in which case look at an aftermarket solution with an 80mm fan. I got an Alpha PAL8150 for mine just for the heck of it, but from the temperatures people have reported versus mine (with the same CPU and mobo), the stock HSF actually cools better than my 8150 does (with a quiet Panaflo L1A 80mm fan).
 
cool, I'm actually going to use a 60mm <=> 80MM converter with a coolmaster 25db fan with it. I got some AS5 so I should be fine. Thanks everyone!

[edit] I just noticed the stock HSF has an 80MM fan so I don't need my adaptor. SWEET!

[edit 2] I was looking at my adaptor, the stock fan isn't 60mm it's [?]70mm[/?] Interesting.... 😕
 
You know, they run so cool, I don't think it really matters, so have fun doing whichever you decide !

Edit: If you do go aftermarkey, my Thermaltake Silent Boost K8 is very quiet, and runs 32c-42c depending on load at about 28c ambient temp.
 
It's not an acronyn, it just means to sand whatever surface to a flat, smooth almost mirror-like finish.
 
Originally posted by: Markfw900
You know, they run so cool, I don't think it really matters, so have fun doing whichever you decide ! Edit: If you do go aftermarkey, my Thermaltake Silent Boost K8 is very quiet, and runs 32c-42c depending on load at about 28c ambient temp.
Click to expand...

It was just an idea I had as I was dreaming about my almost complete system 😀
 
You must log in or register to reply here.

TRENDING THREADS

Back
Top