• We’re currently investigating an issue related to the forum theme and styling that is impacting page layout and visual formatting. The problem has been identified, and we are actively working on a resolution. There is no impact to user data or functionality, this is strictly a front-end display issue. We’ll post an update once the fix has been deployed. Thanks for your patience while we get this sorted.

Yet Another Opteron 939 Thread

K

KristopherKubicki

Golden Member
Hi Everyone,

I am writing an article about Socket 939 Opterons. Can anyone who has a 939 Opteron post their CPU and motherboard here? If you have a problem getting them to work, please also post your info in bold so I can see it really easily.

Thanks!

Kristopher
 
I have an Opteron 170 and an ASRock 939Dual-SATA2 - but I'm waiting on the backplate so I can't mount my heatsink yet (and thus can't do anything else yet of course) 😱

I'll be sure to update when I have it up and running 🙂
 
I've tested:

opteron 148
opteron 146
opteron 146
opteron 146
opteron 146
opteron 146

all with dfi ultra-d (modded to sli-d)

no problems with any chips except the 3rd opteron 146. For some reason that chip wouldnt boot up the first time with 2x1 gig crucial ballistix. i had to switch in another opteron and then switch it out again before it would work.
 
Have the Opty 146 on a MSI Neo 2-F(all parts below) had no problems whatsoever. Not sure if its a memory/mobo thing or the Opty's memory controller but when I get up past 290 HTT its hard to get decent memory timings stable even when using the 133 divider and 2T.
 
Opteron 165 on MSI K8-Neo2 Platinum. Running without a problem, 1.B bios worked fine, using a modded one now for the 150 divider. Other specs as below.
 
Hey PhatoseAlpha could you point me to the beta bios that you are using? I've been dying here with the 133 divider as my ram can't do the speed required for the 166 divider. Any good tips/locations on a good bios for the Neo2's would be awesome!!
 
Opteron 170@2600 on Chaintech VNF4-utra

Had to upgrade bios to v 5.0, no problems before, just didn't see 2 cores.
 
Opteron 165@2.5, MSI Neo2 Platinum, had to update to a newer Bios to be able to see both cores, not a single problem. using Bios W7025NMS V1.CB3
 
Opteron 170 on the EVGA SLI Motherboard .
Model 133-K8-NF41 , bios 4.2



I am very very 😀 with it.
 
All you need to know about my Opteron and its rig, Kris 🙂

CPU/Stepping: Opteron 144 CAB2E 0540 FPMW
Max Stable OC: 2.7ghz @ 300HTT
Voltage: 1.6v
Stability Test: Prime95 small FFTs
Mobo: DFI NF4 Ultra-D
PSU: Enermax 460w 33A/12v 24pin PSU
Memory: 2x512MB Mushkin Blue C2 @ 193mhz 2-3-3-7 1T w/133mhz divider
Cooling: Thermalright SI-120 w/120mm Sunon 85CFM fan
Case/Case Cooling: CM Cavalier w/120mm Sunon exhaust, open side panel, 80mm intake
Ambient room temp: 79F
CPU Idle/Load temps: 38C/50C

Had no issues with the system recognizing and running the CPU 100% flawlessly. I'm using the 6/23 BIOS for my DFI.
 
Hey Kris,
I tried the Opteron 170 on both DFI NF4 SLI-DR (bios 623-2) and the new DFI NF4 SLI-DR EXPERT (shipping bios, 02/11/2005). Runs 100% on both.

Please don't forget to check if COOL AND QUIET (Powernow!) works for the Opteron DUAL CORE, there are a couple of posts with people not able to use it (including myself).
The same is valid on AMD Forums. Most people are not able to.

CPU: Opteron Dual Core 170
Stepping: CCBWE 0534SPMW
Overclocked speed: 2.6GHz (10 x 260)
CPU voltage: 1.47 volts (CPU-Z)
Cooling: Thermalright SI-120 with 120mm Enermax fan
Idle temps: 32C
Load temps: 40C
Motherboard: DFI NF4 SLI_DR Expert BIOS 1102 (stock)
Ram: OCZ4002048ELDCPC, Platinum EL
Ram size: 2048 (2 x 1024Mb)
Ram timings: 2.5-3-3-7
Ram divider: 5:6 (216MHz)
Ram voltage: 2.7 volts

or
Overclocked speed: 2.5GHz (10 x 250)
CPU voltage: 1.39 volts (CPU-Z)
Idle temps: 28C
Load temps: 38C
Ram divider: 9:10 (227MHz)
 

CPU: Opteron 146 CABYE 540
Stepping: CABYE 540
Overclocked speed: 2.9GHz
CPU voltage: 1.50 volts
Cooling: Air
Motherboard: Biostar Tforce 6100 939
Ram: 2X512MB Geil Value
Ram timings: 2-3-3-7
Ram divider: 4:6 (193MHz)
Ram voltage: 2.8 volts


 
My post taken from the Opteron results thread.

Current OC settings

CPU: Opteron Dual Core 165
Stepping: CCBWE 0534SPMW
Overclocked speed: 2.6Ghz
CPU voltage: 1.52 volts
Cooling: Thermalright xp90 with 92mm panaflo fan 47cfm
Idle temps: 41 degrees
Load temps: 53 degrees
Motherboard: MSI K8N Neo2 Platinum BIOS 1.B
Ram: OCZ 3200 Platinum Rev2
Ram size: 1024 (2 x 512Mb)
Ram timings: 2.5-4-4-7
Ram divider: 1:1 289Mhz
Ram voltage: 2.85 volts


Max stable OC which is awaiting water setup as it runs too HOT!!

CPU: Opteron Dual Core 165
Stepping: CCBWE 0534SPMW
Overclocked speed: 2.8Ghz
CPU voltage: 1.62 volts
Cooling: Thermalright xp90 with 92mm panaflo fan 47cfm
Idle temps: 44 degrees
Load temps: 63+ degrees
Motherboard: MSI K8N Neo2 Platinum BIOS 1.B
Ram: OCZ 3200 Platinum Rev2
Ram size: 1024 (2 x 512Mb)
Ram timings: 2.5-4-3-7
Ram divider: 166 @ 280Mhz
Ram voltage: 2.85 volts


Also here is a link to the thread i created which has more info.
 
CPU: Opteron 148

Stepping: CABYE 0540 FPBW

Overclocked speed: 3058 Stable

CPU voltage: 1.424v

Idle temp: 22C or so

Load temp: 28C or so

Cooling: Swiftech Storm/ Eheim 1260/ Chilled water at 52 to 55F

Motherboard: MSI K8N NEO2-F (Bios 1B)

Ram: Mushkin BH-5

Ram size: 2x512

Ram timings: 2,3,3,11, 1T

Ram divider: 166

Ram voltage: 2.85v

FSB: 278

LDT 3x

Still testing for Max stability are higher speeds.
 
CPU: Opteron 148
Stepping: CABYE 0540
Overclocked speed: 2809(11 x 255) CPUZ
CPU voltage: 1.34 volts
Cooling: Thermalright XP90C
Idle temps: 32C
Load temps: 42-43C
Motherboard:Asus A8N-SLI Deluxe Bios 1015
Ram: Corsair 2x512-3200XLPT
Ram size: 2048 (2 x 1024Mb)
Ram voltage: 2.8 volts

I had the Opteron installed with Bios 1014 and it showed AMD unkown CPU in the boot up screen, this did not hinder the overclock or any operation of the computer. I flashed the bios to 1015 and the board recognized the CPU.
 
Hey Madellga, how is the DFI Expert? Did you previously use an Ultra-D or SLI-D? If so, how do they compare?
 
Hi Avalon,

I bought one because a friend of mine wanted my rig - he has nor the time nor the knowledge to build one. I had to buy new components for me: mobo, PSU, CPU (the Opteron).

I decided to give a shot on the Expert, despite the lack of reviews.

I think you are aware that the layout has changed a bit - memory, CPU position - and the PCIex for the video cards are further apart. I didn't see any problems with that. Also SLI works jumperless, but I don't have SLI - no really useful at the moment.

What I can tell you? I installed everything, copied the bios settings from the "older" DFI (there are some new additional settings) and just gave the first try. Windows XP Pro SP2 loaded normally, didn't need to reinstall anything but had to re-activate Windows - which is really a pain in the neck. Had to read the 8 x 6 keys over the tel to the automated bot (internet didn't work), had to repeat again to a real person, explain why I had to activate my Windows again, where I bought it, my underwear color etc etc etc. After 5 minutes, I got the activation key again. Next time I will go with Corp. Copy :disgust:

Back on topic, on my San Diego 3700 I was able to get an extra 100MHz with the Expert (2.8 instead of 2.7 GHz). With the Opteron, I an stuck with 2.6GHz (2.7 didn't work and I didn't try anything between). But I think it is running with a bit less voltage (BIOS options have different values).

Overall, I recommend the new Expert mobo for someone building a new system, but it does not justify you selling your mobo just to upgrade - unless you can easily sell to a friend like I did.

I also didn't have time to tweak the board, DFI Street Forums are a bit slow on this mobo(Angry Games had some sort of problems with DFI staff - some noobs complained about him). I think it has potential to do a bit better but we need to see some reviews from AT or other competent people.

I heard this mobo can do also 4 memory banks with 1T@200MHz, but I don't have the sticks to try. My friend will come near Xmas and will bring his RAM, which is the same as mine. I will try the 1T then.

If you want, I can create a thread and post some pictures. Let me know 😉
 
My 146 should arrive some time next week. I'll be using it on my existing A8V board for about a month (I want a DFI but won't be able to use it without a PCIE video card, and I'm waiting for the prices of the new high end video cards to fall a bit), so I will probably be limited to around 2.6ghz for now. From what I've seen on other forums, this board works with Opterons starting from the 1013 BIOS and supports CnQ on them with the latest 1016.002 BIOS. I'll edit this post with more info once I have it running.
 
Opteron 165, Thermaltake SilentBoost
DFI Infinity NF4-Ultra
2x 1GB PC3200 GEIL Value Ram Rated 3-4-4-8
Sapphire GTO2 - Unlocked, 540/600
Enermax Whisper 465- 430Watt PS
WD 250JB ATA100 OS Drive
Windows XP64

No problems getting the rig to work.
Running the following settings: 256x9 = 2300Mhz, 1.375v | Memory: 6/5 divider (211mhz) 2.5-3-3-7 T1, 2.8v
C-n-Q will NOT work in XP64, even with latest Bios and drivers
Having issues pushing the FSB above ~260, possibly issues with dividers, etc.
 
You must log in or register to reply here.

TRENDING THREADS

Back
Top