Whats your CPU voltage AMD Barton and T-Bred users?

[suklee]

Originally posted by: MegaWorks

Originally posted by: pelikan
1.95V. CPU at 2500 MHz (218 x 11.5). Cooled by chilled water.

holy sh!t man lower your voltage!!! you're gonna burn your cpu

Thats why he has water cooling! Pelikan, what kind of temps are you getting with that setup?

 

[slaves123]

1700+@2000@1.625v (145x11.5)

 

[pelikan]

Originally posted by: Kai920

Originally posted by: MegaWorks

Originally posted by: pelikan
1.95V. CPU at 2500 MHz (218 x 11.5). Cooled by chilled water.

holy sh!t man lower your voltage!!! you're gonna burn your cpu

Thats why he has water cooling! Pelikan, what kind of temps are you getting with that setup?

I'm not too sure about my temps because the sensor on my NF7-S can vary by 10C between boots. It's probably in the mid 20's under load now that I have a cascade block in there. The water is 10-15C.

As far as burning the cpu, who knows? I'm not too worried about it. This barton has seen 1.9V or more for about six months.

 

[Abhoth]

Barton 2800+ / 11x200 @ stock voltage

 

[PCBliss]

Your voltage really is fine at anything unde 2.0 as long as temps are ok. For everyday use i have my unlocked Aqxea week 34 2500+ @ 2.23 stock 1.65 vcore.

 

[MegaWorks]

Originally posted by: PCBliss
Your voltage really is fine at anything unde 2.0 as long as temps are ok. For everyday use i have my unlocked Aqxea week 34 2500+ @ 2.23 stock 1.65 vcore.

I'm not so sure, ppl use to say that going over 1.75v is not recommended and would kill the CPU. Has anyone tried to go over 1.75v with air cooling and still has is CPU running for months?

------------------------------------------------------
AMD Athlon XP T-Bred B DLT3C 1700+ @ 2.3GHZ (1.775v) 400FSB = 3200+
Abit NF7-S V.2 (nforce 2 400U)
Corsair TwinX XMS 3200LL 512MB @ 2-3-2-6 (2.6v)
Sapphire Radeon 9500 Pro 128MB
Antec TrueBlue 480W
Thermalright SLK-947U with 92mm Vantec Tornado @2800RPM
Maxtor 91531U3 15GB
2x Western Digital WD400BB 40GB serials
Antec PlusView 1000AMG
Cambridge SoundWorks MegaWorks THX 550 5.1

 

[ahfung]

After upgrade to Cascade, my 1800+ managed to run at 2606MHz@1.9V with 24x7 stablity. It can even boot into windows at 2735MHz and barely stable enough to run a few benchmarks.

My old Maze4 only got it overclocked to 2.5GHz@1.85V for daily usage. Could never get inside windows at 2.7GHz at any voltage.

 

[MegaWorks]

Originally posted by: ahfung
After upgrade to Cascade, my 1800+ managed to run at 2606MHz@1.9V with 24x7 stablity. It can even boot into windows at 2735MHz and barely stable enough to run a few benchmarks.

My old Maze4 only got it overclocked to 2.5GHz@1.85V for daily usage. Could never get inside windows at 2.7GHz at any voltage.

OMG!!! 2.6GHZ thats like Athlon XP 3800+ WOW! :beer:
but for how long do you have this setup?

------------------------------------------------------
AMD Athlon XP T-Bred B DLT3C 1700+ @ 2.3GHZ (1.775v) 400FSB = 3200+
Abit NF7-S V.2 (nforce 2 400U)
Corsair TwinX XMS 3200LL 512MB @ 2-3-2-6 (2.6v)
Sapphire Radeon 9500 Pro 128MB
Antec TrueBlue 480W
Thermalright SLK-947U with 92mm Vantec Tornado @2800RPM
Maxtor 91531U3 15GB
2x Western Digital WD400BB 40GB serials
Antec PlusView 1000AMG
Cambridge SoundWorks MegaWorks THX 550 5.1

 

[MegaWorks]

what is cascade?

------------------------------------------------------
AMD Athlon XP T-Bred B DLT3C 1700+ @ 2.3GHZ (1.775v) 400FSB = 3200+
Abit NF7-S V.2 (nforce 2 400U)
Corsair TwinX XMS 3200LL 512MB @ 2-3-2-6 (2.6v)
Sapphire Radeon 9500 Pro 128MB
Antec TrueBlue 480W
Thermalright SLK-947U with 92mm Vantec Tornado @2800RPM
Maxtor 91531U3 15GB
2x Western Digital WD400BB 40GB serials
Antec PlusView 1000AMG
Cambridge SoundWorks MegaWorks THX 550 5.1

 

[pelikan]

Originally posted by: MegaWorks

Originally posted by: PCBliss
Your voltage really is fine at anything unde 2.0 as long as temps are ok. For everyday use i have my unlocked Aqxea week 34 2500+ @ 2.23 stock 1.65 vcore.

I'm not so sure, ppl use to say that going over 1.75v is not recommended and would kill the CPU. Has anyone tried to go over 1.75v with air cooling and still has is CPU running for months?

I ran a tbred 2100+ and a barton on very good air cooling with 1.9V for months on end. No problems. You have to have good case ventilation and cpu cooling to keep it stable with that voltage though. Watercooling just makes the heat easier to deal with.

 

[ahfung]

2.6GHz@1.9V has been running for almost 3 months 24x7.

For those who don't know a lot about watercooling, Casacade is the most famous and best performancing waterblock made by a watercooling enthusiastic hobbyist called Cathar.

 

[AkumaX]

umm... 1.5v? i think that's the stock vcore on my thorton... (2000+ @ 2.2ghz)

 

[Dustswirl]

2500 @ 3200 speed Vc=1.65V, currently oced more as seen below

cheers!

 

[NEVERwinter]

Tbred 1700 @ 10x210MHz = 1.675V

 

[hytek369]

1800+ at 2.4 on 1.80volts

 

[MegaWorks]

I'm thinking of buying a watercooling setup, are the swifttech waterblocks good performers for example the MCW5000-A-02 waterblcok.

------------------------------------------------------
AMD Athlon XP T-Bred B DLT3C 1700+ @ 2.3GHZ (1.775v) 400FSB = 3200+
Abit NF7-S V.2 (nforce 2 400U)
Corsair TwinX XMS 3200LL 512MB @ 2-3-2-6 (2.6v)
Sapphire Radeon 9500 Pro 128MB
Antec TrueBlue 480W
Thermalright SLK-947U with 92mm Vantec Tornado @2800RPM
Maxtor 91531U3 15GB
2x Western Digital WD400BB 40GB serials
Antec PlusView 1000AMG
Cambridge SoundWorks MegaWorks THX 550 5.1

 

[pelikan]

Originally posted by: MegaWorks
I'm thinking of buying a watercooling setup, are the swifttech waterblocks good performers for example the MCW5000-A-02 waterblcok.

The D-Tek whitewater is your best bet as the cascade is not available.
Overclockers watercooling forums is a great place for info.

 

[Abzstrak]

have my barton core 2500+ at 2500MHz @ 1.825V 36C idle, 43C under load, air cooled. 200bus at 2-3-2-6 timings, Corsair XMS. heatsink is a volcano 12

 

[Naruto]

Originally posted by: Naruto
My Computer: 1800+ @ 2.2ghz 1.6V (actual 1.58V) DLT3C JIUHB green veiny pcb

My Bro's Computer: 1800+ @ 2.2ghz 1.65V (actual 1.62 ~ 1.63V) DLT3C JIUHB brown pcb

Just boosted to 2.3ghz (11x209) @ 1.63V

 

[Naruto]

Originally posted by: Naruto
My Computer: 1800+ @ 2.2ghz 1.6V (actual 1.58V) DLT3C JIUHB green veiny pcb

My Bro's Computer: 1800+ @ 2.2ghz 1.65V (actual 1.62 ~ 1.63V) DLT3C JIUHB brown pcb

Just boosted to 2.3ghz (11x209) @ 1.63V

 

[MegaWorks]

Originally posted by: Abzstrak
have my barton core 2500+ at 2500MHz @ 1.825V 36C idle, 43C under load, air cooled. 200bus at 2-3-2-6 timings, Corsair XMS. heatsink is a volcano 12

TT Volcano 12 nice, your temp are amazing it's like watercooling!!!
my Thermalright SLK-947U performs very close to your heatsink, but I think your heatsink is better. Damn I should of bought the Volcano 12

------------------------------------------------------
AMD Athlon XP T-Bred B DLT3C 1700+ @ 2.3GHZ (1.775v) 400FSB = 3200+
Abit NF7-S V.2 (nforce 2 400U)
Corsair TwinX XMS 3200LL 512MB @ 2-3-2-6 (2.6v)
Sapphire Radeon 9500 Pro 128MB
Antec TrueBlue 480W
Thermalright SLK-947U with 92mm Vantec Tornado @2800RPM
Maxtor 91531U3 15GB
2x Western Digital WD400BB 40GB serials
Antec PlusView 1000AMG
Cambridge SoundWorks MegaWorks THX 550 5.1

 

[Abzstrak]

Originally posted by: MegaWorks

Originally posted by: Abzstrak
have my barton core 2500+ at 2500MHz @ 1.825V 36C idle, 43C under load, air cooled. 200bus at 2-3-2-6 timings, Corsair XMS. heatsink is a volcano 12

TT Volcano 12 nice, your temp are amazing it's like watercooling!!!
my Thermalright SLK-947U performs very close to your heatsink, but I think your heatsink is better. Damn I should of bought the Volcano 12

I should also add that I have an air induction tube feeding room temp air straight in to my cpu fan... that dropped it about 10C. but yeah, I'm VERY happy with the temps.

 

[pelikan]

Originally posted by: Abzstrak
have my barton core 2500+ at 2500MHz @ 1.825V 36C idle, 43C under load, air cooled. 200bus at 2-3-2-6 timings, Corsair XMS. heatsink is a volcano 12

That's one of the best bartons I've ever heard of. Congratulations.

 

[Rmex]

Originally posted by: MegaWorks

Originally posted by: PCBliss
Your voltage really is fine at anything unde 2.0 as long as temps are ok. For everyday use i have my unlocked Aqxea week 34 2500+ @ 2.23 stock 1.65 vcore.

I'm not so sure, ppl use to say that going over 1.75v is not recommended and would kill the CPU. Has anyone tried to go over 1.75v with air cooling and still has is CPU running for months?

Yes you can run above 1.75 on air. Im at 1.8V, I know thats not much higher than 1.75 but still. Iv been running it for a full year at 1.8v-2240mhz; and ive run it at 1.85 for a few months before aswell.

temps are - Idle 52c, load 57c

at 1.85, temps were 56c idle and 62c load...backed it down to 1.8 only because the oc gain was in the area of diminishing returns plus the additional heat/potential risk factored in abit to.

From my experience, as long as you dont go above 58-60c during load then your cpu will be fine, but above 1.85 i dont know if thats still the case.

 

[MegaWorks]

bump

------------------------------------------------------
AMD Athlon XP T-Bred B DLT3C 1700+ @ 2.3GHZ (1.775v) 400FSB = 3200+
Abit NF7-S V.2 (nforce 2 400U)
Corsair TwinX XMS 3200LL 512MB @ 2-3-2-6 (2.6v)
Sapphire Radeon 9500 Pro 128MB
Antec TrueBlue 480W
Thermalright SLK-947U with 92mm Vantec Tornado @2800RPM
Maxtor 91531U3 15GB
2x Western Digital WD400BB 40GB serials
Antec PlusView 1000AMG
Cambridge SoundWorks MegaWorks THX 550 5.1