problems with RC5 registering

[Homerboy]

http://stats.distributed.net/rc5-64/psummary.php3?id=299252

Well ihave RC5 runing on 2 machines right now.. one is a PII 266 and seems to register JUST FINE...

The other is a 2x550 that I just recently formated and reinstalled RC5 on... but by looking at my stats, I don't think the RC5 on the 2x550 is registering at all.

ALL the options are default, and it is crunching away and a nice speedy clip..

Any ideas?

PS - I do apologize, I need to get my 800 and 200 Mhz machines back up and running too.. I jsut re-did EVERYTHING and just havent had th time to toss RC5 on thos yet.

 

[Engine]

>>ALL the options are default

Even the email address? If so, that would explain your problem right there 🙂
Just set the email address in the client to yours, and the blocks'll register just fine.

 

[Dougal]

That would be about the only thing I could think of as well Engine.

 

[Homerboy]

email address is the correct one... Thats the one thing I changed in the set up.

 

[Postman]

If the settings are at default it might be possible that the client is doing OGR. You sure that it says cracking RC5 on the client's window when it's open?

 

[Homerboy]

ARGGHHHH!!!!!

http://stats.distributed.net/ogr-24/psummary.php3?id=299252

your right! SInce when did this option become a choice?

How do I switch over? (I am however screaming up the OGR charts =))

 

[Homerboy]

wait a minute....

[Jul 19 14:28:02 UTC] Loaded OGR stub 24/7-1-22-3-12
[Jul 19 14:28:02 UTC] Summary: 1 OGR packet (6.47 Gnodes)
0.00:30:08.20 - [3.58 Mnodes/s]
[Jul 19 14:28:02 UTC] 23 OGR packets (23 work units) remain in buff-in.ogr
[Jul 19 14:28:02 UTC] 1 OGR packet (1 work unit) is in buff-out.ogr
.....10%.....20%.....30%.....40%.....50%.....60%.....70%.....80%.....90%....100
[Jul 19 15:46:16 UTC] Completed RC5 packet BA3D9D04:60000000 (8*2^28 keys)
0.01:29:17.00 - [400,874.30 keys/sec]
[Jul 19 15:46:16 UTC] Loaded OGR stub 24/7-1-22-3-13
[Jul 19 15:46:17 UTC] Summary: 2 RC5 packets (16*2^28 keys)
0.01:48:22.92 - [545.24 kkeys/s]
[Jul 19 15:46:17 UTC] 5 RC5 packets (24 work units) remain in buff-in.rc5


WTF am I running?!

 

[ViRGE]

From the FAQ:


<< 3) Now, configure the client to run RC5. To do this, again go into the configuration menu, then type 2(Buffer and buffer update options) and then 9(Load-work precedence). From there, clear the &quot;settings&quot; line, and replace it with the following:

RC5,OGR=0,DES=0,CSC=0

Then press &quot;enter&quot; to save this new setting, then &quot;0&quot; twice to exit the configuration screen and save any new settings. >>



Oh, and homerboy, the client's default is set to run OGR, then RC5, then update its buffers, and start again.😉

 

[Homerboy]

ahhhh yes!!!!

here come the keys!!!!

thanks kids!

As always Anantech (even more so Team Anantech) comes through in a pinch.