paying for 6mbit and getting 4.9
sigh. originally i was getting pretty close to 6mbit but it just keeps getting slower
. should just get charter but its kinda expensive.
edit:
i think it is a problem fixable by interleaving, as i'm getting 40.9 downstream attenuation, but when i called tech support and asked if they could set up interleaving on the line, the guy essentially called me a noob
and said i set up my router wrong... sigh :\ he didn't even set up the line interleaving. I think this also might be why i sometimes get page will not load errors and have to refresh, and my modem has so many unrecoverable errors :S
Statistics
Collected for 18 days 0:15:06
Since Reset Current 24-Hour Interval Current 15-Minute Interval Time Since Last Event
ATM Cell Header Errors: 7778 23 0 2:31:43
ATM Loss of Cell Delineation: 1287 2 0 7:31:25
DSL Link Retrains: 12 0 0 1 day 13:11:18
DSL Training Errors: 1 0 0 18 days 0:14:38
DSL Training Timeouts: 0 0 0 0:00:00
DSL Loss of Framing Failures: 21 0 0 1 day 13:11:19
DSL Loss of Signal Failures: 21 0 0 1 day 13:11:19
DSL Loss of Power Failures: 0 0 0 0:00:00
DSL Loss of Margin Failures: 21 0 0 1 day 13:11:19
DSL Cumulative Errored Seconds: 7175 42 0 0:04:41
DSL Severely Errored Seconds: 64 0 0 1 day 13:11:19
DSL Corrected Blocks: 0 0 0 0:00:00
DSL Uncorrected Blocks: 12629 44 0 0:04:41
ISP Connection Establishment: 6 6 6 3:59:21
also i can't seem to figure out how to format the columns on this D:, it looks so ugly like that. if someone could tell me how (and it's easy) that'd be nice, thanks.
edit:
It sounds like your phone line actually sucks. If you're getting 4.9, you're probably on a 5200K profile, which is what they put you on if you're not close enough to the central office to get a strong enough signal.
Call ATT tech support and have them check your provisioned speed and your relative capacity. If your capacity is near 100%, see if they can put your circuit on "Interleave". This mode will increase latency a bit, but stabilize the circuit and possibly give you better performance.
i think it is a problem fixable by interleaving, as i'm getting 40.9 downstream attenuation, but when i called tech support and asked if they could set up interleaving on the line, the guy essentially called me a noob
Statistics
Collected for 18 days 0:15:06
Since Reset Current 24-Hour Interval Current 15-Minute Interval Time Since Last Event
ATM Cell Header Errors: 7778 23 0 2:31:43
ATM Loss of Cell Delineation: 1287 2 0 7:31:25
DSL Link Retrains: 12 0 0 1 day 13:11:18
DSL Training Errors: 1 0 0 18 days 0:14:38
DSL Training Timeouts: 0 0 0 0:00:00
DSL Loss of Framing Failures: 21 0 0 1 day 13:11:19
DSL Loss of Signal Failures: 21 0 0 1 day 13:11:19
DSL Loss of Power Failures: 0 0 0 0:00:00
DSL Loss of Margin Failures: 21 0 0 1 day 13:11:19
DSL Cumulative Errored Seconds: 7175 42 0 0:04:41
DSL Severely Errored Seconds: 64 0 0 1 day 13:11:19
DSL Corrected Blocks: 0 0 0 0:00:00
DSL Uncorrected Blocks: 12629 44 0 0:04:41
ISP Connection Establishment: 6 6 6 3:59:21
also i can't seem to figure out how to format the columns on this D:, it looks so ugly like that. if someone could tell me how (and it's easy) that'd be nice, thanks.
Last edited: