Post your CPU Temps / HSF specs!

[Schmeph]

Soyo KV7 Dragon+
XP1700+
SK-6 HS W/38 CFM Fan
CPU-29/30 Idle 35/36 Load (Prime95 2hrs)
Case 22 Idle 24/25 Load

 

[Jen]

Abit KG7 with a 1800+ running 1725mhz i got 34c at idle and 44c under load.

Heatsink is a Alpha 8045 with sunon fan


second system is

Epox 8k7a with a 1.33 thunderbird at 1.6 2 volts........h2o for cooling.........38c idle........full load 45c


Jen

 

[Kanalua]

I've got a problem...

My girlfirends COmputer:
1.4Ghz @ 1.47Ghz
MSI K7T Turbo Limited
250Wt PS

Here's the Problem...
71 degrees C CPU temp!!!!No internal fans, nothing, except Thermaltake Volcano 5 CPU HS/Fan

Thinking of putting a intake fan at the front of the computer, what else can I do to bring the temp down! I lowered the FSB and took it back to 1.4Ghz...but don;t know if that will do enough...

 

[WA261]

that temp is horrible...are you using asii? if not..get some!! =) also get some intakes and exhasut going

 

[murphy55d]

I had horrible temp problems with a Volcano 5 as well. Not 71, but I did have an intake fan and 2 blowing out the back.

I just put a Vantec 6035D on, and it's WAAYYYYYYYYYYY cooler.

 

[Mikewarrior2]

Kanalua,

The k7t-turbo reads "higher" than most other motherboards.... depending on your ambient systme temps on that system, they may be fairly normal based on the cooler/motherboard you are using.



Mike

 

[BeauJangles]

Tbird 1.2 @ 1.4
31 c idle, 34 c full load. Silent
(Maze2 rippoff waterblock)

 

[de8212]

XP 1600
Epox 8kha+
Volcano 7

CAse temp 20C, cpu 32c idle. CPU temp after exiting an hour of UT was 36.

de

 

[chopstxxx]

<< enlight 7237 w/:
80mm sunon 42 cfm front intake
60mm sunon 24 cfm lower front side intake
92mm ?????? ?? cfm side intake
80mm sunon 39 cfm rear exhaust
pci slot fan
60 mm exhaust on bottom of psu
3x40mm exhaust on front of psu
80mm exhaust on back of psu(stock psu fan)
3x40 hard drive cooler
2coolpc plus fan and duct system(92mm fan)
northbridge cooling fan
thermaltake mini copper orb hsf (soon to be thermalright sk-6 w/ 42 cfm sunon)

iwill kk-266
1.33 tbird@ 1.50
ambient =21
case = 23
cpu = 44 >>



Just got my sk-6, temps dropped to 33!!!

 

[Kanalua]

WA261, murphy55d, Mikewarrior2: Thanks for the suggestons. I went out and got a intake fan and some Arctic Silver Thermal paste, temps dropped ~mid-60s C. Better than the mid-high 70s it was giving before.

 

[Jerboy]

<< If you really want more accurate temps get an LCD monitor. Like this one! I am using it. Mobo says cpu @full load is 37c but LCD shows 43c. This alone shows what a difference the mobo shows. Even LCD is not 100% right. But much closer! >>





accurate?? where's calibration certificate for that thing?

 

[SickBeast]

Athlon Tbird at 1600mhz
39C idle
43C loaded
OCZ gladiator /w 5000rpm fan
2 x 120mm case fans, both intake

 

[coocoo]

XP1600 1.4@1.6
Alpha PAL8045 with 80mm fan.
Room: 22C

Was:
Delta 68.5CFM 80mm fan for CPU (blowing) and 130CFM Y.S.Tech 120mm at side blow hole.
CPU idle/loaded: 32/32 C
MainBoard: 24C

The Delta is too loud. I swapped it with a Y.S.Tech.

Now:
Y.S.Tech 48.5CFM 80mm (suction mode) and 130CFM Y.S.Tech 120mm at side blow hole.
CPU idel/loaded: 38/42C
MainBoard: 28C

Any one uses Delta with rheostat? How much noise can be reduced?

 

[Theslowone]

1ghz athlon @1.33ghz 266fsb
Leadtek 7350kda mobo
Vantec 6027d HS W/asII
two 80mm case fans
Enermax 350w ps with a 92mm and 80mm fan
Full load 54C cpu
Idle 46C cpu
Full load case 32 Idle 30C
Room temp 23C

 

[SuperPickle]

t-bird 1.33@1.47 (140X10.5)
KG-7 RAID
SK-6 w/ Sunon 38cfm 80MM
2X120mm Panaflo H1A switchable on/off side intakes @7v
2X120mm Panaflo M1A switchable on/off top blowholes @7v
in generic full tower

41~45 loaded depending on ambient

Switching from 7v to 12v dips my load 1 or 2 degrees