Calling all e6700/P5WDH Users!

[LittleNemoNES]

EDIT: New info

IDLE: 27C CPU, 40C mobo with low fan settings (25, 35 high speed)
LOAD: 50 CPU, 45 Mobo low fan (48, 35 high speed)


Jumper Free
------------------------
AI OC= Manual
CPU FREQ= 350
DRAM FREQ= DDR2-700mhz

Performance Mode= Auto
PCI eXpress Freq= 110 (many people swear by it in the XtremeOC forum)
PCI clock Sync Mode= 33.33
Memory V= 2.20V
CPU Vcore= 1.550

FSB Termination V= 1.4
MCH Chipset V= 1.65
ICH Chipset V= 1.20
-------------------------
Microcode=ON
All others disabled.
-------------------------
Mem: 4,4,4,15,5
Disabled
Disabled
Disabled

Some things to keep in mind are:
I have crappy value select ram so you may get tighter timings with yours.
I MAY have overvolted the n.bridge (MCH) but it's not an issue since it's not enough to cause any problems.

BTW, I lapped every heatsink in my damn rig and recommend all to do so as well. I used 350, 600, 800, 1000, and 2000 grit to do the jobs. You can get these @ Advance Auto Parts or something similar.

OLD:
So far I have gotten to 333 FSB. @ 1.45 vcore (very cool 45 load). The problem is that orthos will error on me if I do 340 fsb no matter how much voltage I throw @ it...

It's kinda off that this happens.

What settings are you using? BTW I have corsair value ram.

 

[JAG87]

put more volts into MCH, ICH and FSB. Set vcore to 1.5. That will take you to 3.6 ghz.

 

[LittleNemoNES]

I realized I need to overvolt to combat the voltage droop...
Doing 1.5vcore w/3.5Ghz now...still testing prime for at least a half hour.
Thanks ;-)

I know that my rig can go further since temps are pretty damn good. 35*C for mobo despite crossfire and a 100% CPU @ 45*C...

I hope I can do 3.666 @ least (1Ghz OC)

EDIT doing 3.6 with 1.56vcore

 

[LittleNemoNES]

Gonna stick with 3.5 @ 1.5vcore. 3.6 gets too hot. Maybe I can squeeze 50mhz more but I gotta give it some headroom.

Thanks for the help.
IF anyone needs help feel free to PM me.

 

[renozi]

How are your load temps gersson?

And if you don't mind your bios settings?

FSB:
DRAM:
PERFORMANCE:
VDIMM:
VCORE:

SPD: Disabled
TIMING:
HYPERPATH 3: Disabled

And any other settings that might be important...thanks gersson

 

[LittleNemoNES]

IDLE: 27C CPU, 40C mobo with low fan settings (25, 35 high speed)
LOAD: 50 CPU, 45 Mobo low fan (48, 35 high speed)


Jumper Free
------------------------
AI OC= Manual
CPU FREQ= 350
DRAM FREQ= DDR2-700mhz

Performance Mode= Auto
PCI eXpress Freq= 110 (many people swear by it in the XtremeOC forum)
PCI clock Sync Mode= 33.33
Memory V= 2.20V
CPU Vcore= 1.550

FSB Termination V= 1.4
MCH Chipset V= 1.65
ICH Chipset V= 1.20
-------------------------
Microcode=ON
All others disabled.
-------------------------
Mem: 4,4,4,15,5
Disabled
Disabled
Disabled

Some things to keep in mind are:
I have crappy value select ram so you may get tighter timings with yours.
I MAY have overvolted the n.bridge (MCH) but it's not an issue since it's not enough to cause any problems.

BTW, I lapped every heatsink in my damn rig and recommend all to do so as well. I used 350, 600, 800, 1000, and 2000 grit to do the jobs. You can get these @ Advance Auto Parts or something similar.

 

[renozi]

Thanks gersson. Mine fail at 1.5v after 10 mins of orthos blend. I'll go buy some sandpaper 2m and lap my heatsinks and try again at 1.550 adjusted for vdroop.

 

[LittleNemoNES]

you're welcome. I even lapped my e6700! was worth it

 

[lopri]

My board temps never rose above 40C according to software readings. Most of the time it stays below 35C even with 100% load. The reality came in after I tried some shooting (thermo-gun) around VRM area.

 

[renozi]

what was your reality check like lopri?

 

[lopri]

It was like 54~57 for the hottest spots. Temps varies inch by inch on many ASICs and part of the PCB, though. I memsink'ed like crazy the whole board and put a fan blowing onto MOSFET area. My board now does 425FSB with DDR2-850 / 3-3-3. Before the active cooling I had to loosen the timing to 3-4-3.