answered-ish

[Fullmetal Chocobo]

I'm adding another switch to this for my secondary power supply. But I have to drill through the plastic front piece as well as the circuit board to run the cable to the switch. Is this feasible, or should I just run it around the PCB at the expensive of it looking like arse?
Tas.

 

[Zim Hosein]

Originally posted by: tasburrfoot78362
I'm adding another switch to this for my secondary power supply. But I have to drill through the plastic front piece as well as the circuit board to run the cable to the switch. Is this feasible, or should I just run it around the PCB at the expensive of it looking like arse?
Tas.

Your best bet would be to run it around the PCB IMO 🙂

 

[mugs]

Uh... use a drill.

 

[Eli]

A drill bit will have no problem with a PCB.

 

[Zim Hosein]

The main issue here is if tasburrfoot78362 has to ask us, do you really want him/her using power tools on his/her rig? 😉

 

[Fullmetal Chocobo]

Okay, nevermind. I grabbed a PCB off of a hard drive, and it doesn't crack it or anything, so I am alright. I already drilled the hole in the PCB and the plastic, although the plastic one is a bit too small. Thanks for ya'lls help.
Tas.

 

[Fullmetal Chocobo]

Son of a bitch. I was using my drill instead of teh Dremel, and it chipped the plastic. Ugh, fvck. Oh well. I can still use it though. And it isn't terribly noticeable I think....
Tas.

 

[Zim Hosein]

Originally posted by: tasburrfoot78362
Son of a bitch. I was using my drill instead of teh Dremel, and it chipped the plastic. Ugh, fvck. Oh well. I can still use it though. And it isn't terribly noticeable I think....
Tas.

My point exactly!

 

[Fullmetal Chocobo]

But it didn't really matter either way, because now I just have an extra hole in there. The damned switch wouldn't fit. So I get to go switch hunting while evacuating tomorrow. Woohoo! hehehehe OH well. Time to mod something else now.
Tas.

 

[SVT Cobra]

you have to keep it on low speed and keep the bit clean for it not to crack...its almost like cutting plexi glass but a lot safer and easier...

anyways Wrong Forum

 

[Zim Hosein]

Originally posted by: Son of a N00b
you have to keep it on low speed and keep the bit clean for it not to crack...its almost like cutting plexi glass but a lot safer and easier...

anyways Wrong Forum

Ummm... there's a "drilling through PCB" forum? 😕

 

[SVT Cobra]

Originally posted by: Zim Hosein

Originally posted by: Son of a N00b
you have to keep it on low speed and keep the bit clean for it not to crack...its almost like cutting plexi glass but a lot safer and easier...

anyways Wrong Forum

Ummm... there's a "drilling through PCB" forum? 😕

no there is a case and mdding forum though

you have been here how long?

 

[Zim Hosein]

Originally posted by: Son of a N00b

Originally posted by: Zim Hosein

Originally posted by: Son of a N00b
you have to keep it on low speed and keep the bit clean for it not to crack...its almost like cutting plexi glass but a lot safer and easier...

anyways Wrong Forum

Ummm... there's a "drilling through PCB" forum? 😕

no there is a case and mdding forum though

you have been here how long?

Long enough! 😉

 

[SVT Cobra]

Originally posted by: Zim Hosein

Originally posted by: Son of a N00b

Originally posted by: Zim Hosein

Originally posted by: Son of a N00b
you have to keep it on low speed and keep the bit clean for it not to crack...its almost like cutting plexi glass but a lot safer and easier...

anyways Wrong Forum

Ummm... there's a "drilling through PCB" forum? 😕

no there is a case and mdding forum though

you have been here how long?

Long enough! 😉

:laugh::beer: and cheers zim