Recent content by imaxcpu

Yes but what about the Creative Labs 3D Blaster VLB for the vesa local bus? When does that come out? :)

920 DO's? cough....vcore @ 1.36.....with one fan she was stable at 4.48...with 12gb ram 8-8-8-24. Maybe less after the AS5 setup, but this was just out of the box and we will have to vist the max and the min again sometime soon. The 24/7 setup right now has been 1.32 v 4.2 12gb...

Been using Asus for the past ten years, from AMD-athlon to latest Intel I7 I have not had any issues that were a matter of quality or defect. As abusive as I have tried to be they just wont die for me. I am trying really hard to kill this one right now...Die you @#$% Asus MotherBoard die!

Mr.Loyd's experience was more about software hiccups than anything, he should have repaired his OS install or maybe even looked at his PSU if anything as he later concedes in the comments section. Realizing it could have saved him a heck of a lot of trouble as well as inexcusably blaming the...

You really think? Try running all dims full on any I7 near these speeds and watch what happends to the IMC and temps. But maybe there is still room for dropping voltage here n there...and pushing the clock up still. What would help is to get the room down to 72 or so....the heat in this place...

Ambiant room 76f idle both 39-42C Prime 95 20 minutes 68-74C Northbridge 35C at idle 42C under load Both settings give similar thermal results for obvious reasons

Have had this board for just two weeks now, all new from Neweeg and it just wont stop. Very good stable board with no issues. 4.48 with no HT for simming or 4.2 with Ht on for 24/7 multitasking It is setup to run Autodesk 3DS 12, Photoshop and FSX, basically a FSX scenery design and...

Deleted Sorry, meant to start a new post.

Loving the ASUS P6X58D Premium.

I ran mine till just recently, ran an old barton mobile 2600xp with the wire trick, overvolted and she ran up in the 3ghz region for years, had that Bliss 7800+ PCE>AGP card in it....memorries OK, If I remember right that sounds like the symtom of the MB battery starting to go, pop in a new...

Jeez, good question, Ok, I have CPUID monitor, Everest, Sandra, and Its reading so may sensors I cant Id the Northbridge...help! Ths does have very nice heatsinks, so nice in fact I didnt bother with taking them off and putting some AS5 with new fastners (I like to use SSteel Screws, Springs...

Well then we will just have to post pix of the rig..in a day or so

CPU - 1.35v qpi - 1.35v pll 2.0v dram 1.64v Haven't tried finding any max low/high values yet, should be able to lower the ram and maybe even the cpu.

My new Build P6x58d Just a quick update (updated 12-25-09): So far very impressed, I love this new board! Running under load the temps are stable at 52-58c running steady 24/7 4.14 GHz and 12 Gb of ram running loose at 1600 9-9-9-24 Temps running prime95 8 threads after 20 minutes was a...

I am putting mine together right now, Parts: P6X85D Megahalems (3Rsystems Boss II on the way just to try as well) Patriot 6gb 2000 mhz 8-8-8-24 CoolerMaster 840 BFG 285GTX I have a "p6x58d" post in hereas well that I should update soon. So far, the board is in with the HS installed...