Where to get Dremel and which tools for case modding....

[caenus]

I am in the process of putting a 120mm fan on the side of my case. At first I was thinking of getting a hole saw for a drill but realized that it costs around $25-$30. After seeing that I figured I could get a dremel, pay a little more, but be able to use it for other things. I will probably install a 92mm or 80mm in the front of my case soon as well. I think I saw a Dremel tool kit for around $45 but it was the single speed kit rather than the multi-speed kit which was around $80. Is this single speed kit fine? Also anyone got a link to some sites on the internet that sell these kits. Finally, which tool bits will i need to cut blowholes and sand the edges?

Thanks in advance.

 

[Tschaft]

Walmart sells dremels, Ive got the single speed multipro. It works fine for me, the multispeed would be nice though, but not a neccessity. I would use the reinforced cutting wheels, im not sure what I would use for grounding, i forgot what it is called, accually.

 

[Mykex]

Just dont get the cordless one,Its much cheaper and can be tempting....OOPS The one I bought became hot as heck just drilling few holes and the battery wore down quickly. I returned it and upgraded to the plug in.

 

[caenus]

Thanks, I'll have to check out walmart. Only one near me is about 25min away, but it may be worth the trip. About how much do they cost at walmart? I may try home depot, and this craft store Pearl's. I'm pretty sure I saw a Dremel there a few months ago.

 

[caenus]

I checked prices on walmart.com and the variable speed one is only $58 with tons of attachments. I might just get that. What are some advantages to getting the variable speed dremel over the single speed? Also, if I do get the variable speed corded one, how fast should I set it when I'm cutting out blowholes, or drilling holes for the screws or sanding the edges? Are there any techniques I should know? Should I try practicing on another case before, or can I learn as I go?

Thanks.

 

[TonyG]

I would definatly say practice on another case or a piece of metal about the same thickness. It helps to put masking tape aroung the outer edge of the hole you are cutting out so you do not slip and chip the paint on the case. Getting the multi speed makes it easier to cut plexi glass if you ever decide to put in a window for your computer.

 

[sparkle]

Get yourself the multispeed model. It is more versatile when it comes to materials like plastic, and wood. Also, I think it is lower powered than the multispeed

 

[nickburns]

get the kit from home depot

 

[Mday]

<< What are some advantages to getting the variable speed dremel over the single speed? Also, if I do get the variable speed corded one, how fast should I set it when I'm cutting out blowholes, or drilling holes for the screws or sanding the edges? Are there any techniques I should know? Should I try practicing on another case before, or can I learn as I go? >>



advantage? it's just that, variable allows several speeds, which is more practical than just one speed.

for speed, start slow, then go fast. don't exceed the recommended RPM for the bit you are using.

i hardly recommend a dremel for this, really, it takes forever. i'd rather tell you to get a jigsaw and drill bit. anyway, for cutting the blowhole, use a diamond cutting bit, which is never included in those kits. and use cutting grease which is usually found in real hardware stores. don't forget protective eyewear. YOU NEED IT. i would be blind otherwise (i mean that)... for the screw holes, get a bit slightly larger than 0.125&quot; that is, a bit for your DRILL, and make sure you get a bit meant for cutting metal, i use a cobalt bit. you may want to get bolts to secure the fans. you can use another dremel bit to &quot;sand&quot; the hole so you don't cut yourself.

using a dremel is like using a drill... get used to the rpms (torque)... practice on a piece of wood first, then go to metal...

 

[flippinfleck]

Definately go with Home Depot. I bought the single speed at WalMart cuz it was cheap. I went to HomeDepot three days later and found the multispeed with tons of attachments and a case for $51. I wish I had saved my original box, would have been nice to have the case and flex-shaft.


>edit Oh yeah, was $41 at WalMart for single speed edit<

 

[KouklatheCat]

The multi speed Dremel is great. Definately get the reinforced wheels or you will go through a lot of the others. The NON reinforced wheels shatter easily. Either way you go spend $5 and get some safety goggles (gawd I sound like my HS shop teacher). Five bucks is cheaper then a $25 co pay at the hospital and easier to deal with then a messed up eye. I had the thin wheels break off and leave a couple marks on my face and my safety goggles.

 

[caenus]

Thanks for the info. I was planning on purchasing safety goggles anyway. Is it possible to use the Dremel as a drill to drill screw holes? I'll go check HomeDepot this afternoon.