• We’re currently investigating an issue related to the forum theme and styling that is impacting page layout and visual formatting. The problem has been identified, and we are actively working on a resolution. There is no impact to user data or functionality, this is strictly a front-end display issue. We’ll post an update once the fix has been deployed. Thanks for your patience while we get this sorted.

What should I do with a 1700+ and 2500+ sitting here?

F

FluxCap

Golden Member
Here is the situation:

I had my 1700+ running at 1750mhz(166x10.5)for 6 weeks fine. All of a sudden one day it started to lock on screensavers only, but when I put the 1700+ back to default settings it never froze. I figured something either happened to my machine or my bad luck had struck again. It frustrated me so I ordered a new Barton 2500+ for the heck of it. Well, the barton got here yesterday but before I put it in I decided to overclock my 1700+ to the 2500+'s speed (166x11) and it runs like a charm and 46c on full load. Should I even bother opening the retail package on my barton? When I first tried to overclock my 1700+ I tried 2ghz but it was unstable so maybe my chip is not up to it or maybe I should mess with the voltage. At any rate, I don't know what to do. I had planned on putting the Barton in about an hour (after work) but not I am not so sure.

I got the Barton from newegg and it is unopened like I said, do I just have to pay shipping to get it back to them with no extra charge?


Also, just a small note, on 3d scores:

1700+ (stock) w/ 3dmark2001se = 6969
1700+ (barton speed) w/ 3dmark2001se = 7024

What a small gain, very sad.
 
Possibly, but another reason I asked, and should have mentioned in the original post, is that my RAM will be the limiting factor in the long run. (PC2700 Hyper X) I don't think the gains that I could make with the Barton would be much more than the 1700+ pushed a tad harder. The real issue is probably my video card, wouldn't I be better served getting a newer video card for the best gains? Rereading this it sounds like I just answered my question but I am on the fence here with no real decision close to being made.
 
If you can make out the week and stepping on the 2500+ without opening it please LMK and if it's the right one I'll buy it off you 😉
 
Originally posted by: FluxCap
Here is the situation:

I had my 1700+ running at 1750mhz(166x10.5)for 6 weeks fine. All of a sudden one day it started to lock on screensavers only, but when I put the 1700+ back to default settings it never froze. I figured something either happened to my machine or my bad luck had struck again. It frustrated me so I ordered a new Barton 2500+ for the heck of it. Well, the barton got here yesterday but before I put it in I decided to overclock my 1700+ to the 2500+'s speed (166x11) and it runs like a charm and 46c on full load. Should I even bother opening the retail package on my barton? When I first tried to overclock my 1700+ I tried 2ghz but it was unstable so maybe my chip is not up to it or maybe I should mess with the voltage. At any rate, I don't know what to do. I had planned on putting the Barton in about an hour (after work) but not I am not so sure.

I got the Barton from newegg and it is unopened like I said, do I just have to pay shipping to get it back to them with no extra charge?


Also, just a small note, on 3d scores:

1700+ (stock) w/ 3dmark2001se = 6969
1700+ (barton speed) w/ 3dmark2001se = 7024

What a small gain, very sad.
Click to expand...

fluxcap, you underclocked the 2500+ to 1.47?
 
That CPU should do 2.2-2.3ghz on default vcore, I wouldn't send it back.
 
I figured you would say that 😛

I am going for a case like yours also TN, check the For Sale/Trade section the Lian-Li is on the block.
 
Well, I am confused, my PC is rock solid stable in all tests at 166x11 but as soon as I go to 170x11 it gives me long beeps in intervals of 2 seconds and won't post. I think maybe my ram can't cut it.
 
You must log in or register to reply here.

TRENDING THREADS

Back
Top