some asus a8r32-mvp problems (bios 0502)

[LOUISSSSS]

forgive me guys but help me out here:

i'm trying to overlcok my amd x2 4800+ toledo (939 socket)
mb: asus a8r32-mvp deluxe (0502 bios)

my system is exactly as in signature, my ram is OCZ Platinum PC3200 DDR400 Rev2 2-3-3-5
can someone take a look and see what i'm doing wrong and why i can't change the CPU frequency?
here are my settings in bios:

ADVANCED
_Jumper Free Configuration
_AI Overclocking__________________Manual
_CPU Frequency__________________200 (I CAN'T SEEM TO CHANGE THIS FOR SOME REASON)
_PCIE Frequency_________________100

_FID/VID Change__________________Manual
_Processor Frequency Multiple______X12
_Processor Voltage_______________1.400V
_DDR Voltage____________________2.70V
_VCORE Voltage__________________+200mV
_Northbridge Overvolt______________Enabled
___Core Voltage__________________1.4V
___HT Bus Voltage________________1.4V
___PCIE Voltage__________________1.4V

_PEG Link Mode___________________Auto
_PEG Buffer Length________________Auto

_AI Clock SkewA__________________Auto
_AI Clock SkewB__________________Auto

_CPU Configuration
_GART Error Reporting______________Disabled
_MTR Mapping____________________Continuous
_Cool N Quiet_____________________Disabled
_HT Link Speed___________________1 GHz

_Memory Configuration
_Memory Timing Mode_____________Limit
___Memclock Value_______________166
_MCT Timing Mode________________Manual
___CAS (CL)_____________________3.0
___TRAS________________________8
___TRP_________________________3
___TRCD________________________3
___TRRD________________________AUTO
___TRC_________________________AUTO
___TRFC________________________AUTO
___TRWT________________________AUTO
_MCT Extra Timing Mode___________Manual
___TREF________________________7.8us
___DDR Input Strobe Skew_________Disabled
___Burst2Opt____________________Disabled
_User Configuration Mode__________Manual
___Read Preamble________________5.5ns
___Asyc Latency_________________7.0ns
___CMD-ADDR Timing_____________1T

_Bank Interleaving_________________Auto
_Burst Length____________________8 Beats
_Software Memory Hole____________Disabled

_ECC Configuration
___DRAM ECC Enable______________Disabled
___L2 Cache BG Scrub_____________Disabled
___Data Cache BG Scrub___________Disabled

_Chipset
___VGA Priority___________________1st PCIE ->2nd PCIE

_HT Config
___HT Link Speed_________________1 Ghz
___CPU:RD580-NB HT Link Width____16 Bit

___RD580 HT Link Three State_______Disabled
___RD580 HT Drive Strength_________Optimal
___HT Receiver Comp. Ctrl__________Optimal

___RD580 HT PLL Control___________ High Speed

_PCI-E Configuration
___PCIE GFX1 Link Width___________X16
___PCIE GFX2 Link Width___________X16

___P2P Writes Between GFX Ports___Disabled
___10% Extra Current Between GFX__Enabled
___10% Extra Current Between GPP__Enabled
___10% Extra Current Between SB___Enabled
___10% Extra Current Between GFX1_Enabled
___10% Extra Current Between GFX2_Disabled

cross post from CPU section, dunno where to post

 

[Regalk]

I have a hard time getting over 290FSB with 0602 bios (latest)
I have OCZ Gold memory rated at 2.5 4 4 9 (PC4000) and an Opty148

Jumper Free Configuration
_AI Overclocking__________________Manual
_CPU Frequency__________________277
_PCIE Frequency_________________100

_FID/VID Change__________________Manual
_Processor Frequency Multiple______X10
_Processor Voltage_______________1.4250V
_DDR Voltage____________________2.80V
_VCORE Voltage__________________+200mV
_Northbridge Overvolt______________Enabled
___Core Voltage__________________1.4V
___HT Bus Voltage________________1.4V
___PCIE Voltage__________________1.4V

_
HT Link Speed___________________800

_Memory Configuration
_Memory Timing Mode_____________Limit
___Memclock Value_______________183
_MCT Timing Mode________________Manual
___CAS (CL)_____________________2.5
___TRAS________________________9
___TRP_________________________4
___TRCD________________________4
___TRRD________________________2T
___TRC_________________________12T
___TRFC________________________16T
___TRWT________________________2
_MCT Extra Timing Mode___________Manual
___TREF________________________7.8us
___DDR Input Strobe Skew_________Disabled
___Burst2Opt___________________Enabled
_User Configuration Mode__________Manual
___Read Preamble________________6.0ns
___Asyc Latency_________________8.0ns
___CMD-ADDR Timing_____________1T

_Bank Interleaving_________________Auto
_Burst Length____________________8 Beats
_Software Memory Hole____________Disabled
_Chipset
___VGA Priority___________________1st PCIE ->2nd PCIE

_HT Config
___HT Link Speed_________________800
___CPU:RD580-NB HT Link Width____16 Bit

I think those are my settings - I will check later since that rig is not available currently (You may want to try lowering your multiplier and increasing FSB. Memory dividers will be key ( I use memfreq1.1 to play around with various settings). Flash to latest bios available (in DOS mode not windows)