HIGH OIL TEMPERATURE 001
LOW OIL PRESSURE 002
HIGH OIL PRESSURE 003
OIL FILTER<S> HIGH PRESSURE DIFFERENTIAL 004
OIL PUMP OVERLOAD 005
OIL PUMP SURGE 006
MOTOR OVERLOAD<S> 007
MOTOR<S> TEMPERATURE HIGH 008
GENERATOR OVERSPEED 009
GENERATOR OVERCURRENT 010
GENERATOR TEMPERATURE HIGH 011
GENERATOR TOTAL FAILURE 012
COMPRESSOR MOTOR TEMPERATURE HIGH 013
COMPRESSOR MOTOR OVERCURRENT 014
COMPRESSOR MOTOR STALLED 015
MAIN POWER IMBALANCE > 10% BETWEEN PHASES 016
POWER LOSS AT D-8 017
OVER VOLTAGE AT A-2 018
UNDER VOLTAGE AT A-2 019
D.C. SUPPLY TEMPERATURE HIGH 020
D.C. SUPPLY REVERSED 021
+15 VOLT POWER SUPPLY FAILURE 022
-15 VOLT POWER SUPPLY FAILURE 023
+12 VOLT POWER SUPPLY FAILURE 024
-12 VOLT POWER SUPPLY FAILURE 025
+5 VOLT POWER SUPPLY FAILURE 026
-5 VOLT POWER SUPPLY FAILURE 027
MAINS OVERCURRENT PROTECTION TRIPPED 028
LIGHTING OVERCURRENT DRIVER TRIPPED 029
LAMP DRIVER<S> SHORTED 030
LAMP DRIVER<S> OPEN 031
BATTERY WIRING/FUSE OPEN 032
ALARM CIRCUIT MALFUNCTION 033
POWER INTERRUPTION--ON LINE AUTO MODE 034
REGULATOR FAILURE 035
CPU FAILURE 036
READ/WRITE ERROR 037
CPU AMBIENT TEMPERATURE HIGH 038
CPU RAM FAILURE 039
CPU BIOS FAILURE 040
CPU EPROM FAILURE 041
CPU DISK BOOT FAILURE 042
COMMUNICATIONS ERROR 043
SERVO WIRING ERROR <SHORTED/OPEN> 044
SERVO LINK MALFUNCTION 045
FAIL SAFE MALFUNCTION 046
SERVO TEMP HIGH 047
P-E SERVO FAILURE 048
X-Y MOTION SERVO FAILURE 049
Y-X MOTION SERVO FAILURE 050
X-Y MOTION TRANSDUCER LOW OUTPUT 051
Y-X MOTION TRANSDUCER LOW OUTPUT 052
X-Y MOTION TRANSDUCER FALSE SIGNAL 053
Y-X MOTION TRANSDUCER FALSE SIGNAL 054
INTERLOCK FAILURE 055
OVERSPEED 056
AUTO LOCKOUT 056
START SEQUENCER OUT OF CALIBRATION 057
MOTION <AUTO> SEQUENCER OUT OF CALIBRATION 058
OPEN/CLOSE CONFIRMATION FAILURE 059
INSPECTION TIME OUT 060
FALSE SERVO SIGNAL--MOTION 061
MOTION BRAKE SIGNAL LOSS 062
MOTION/ROLL SENSOR FALSE SIGNAL 063
MOTION/ROLL SENSOR FAILURE 064
MOTION/ROLL SENSOR LOW SIGNAL 065
LIFT TENSION SENSOR SIGNAL LOW 066
LIFT TENSION SENSOR FAILURE 067
LIFT TENSION SENSOR FALSE SIGNAL 068
UPPER MECHANICAL LIMIT REACHED 069
UPPER PRE-PROGRAMMED MECHANICAL LIMIT EXCEEDED 070
UPPER MECHANICAL LIMIT SWITCH TRIPPED 071
LOWER MECHANICAL LIMIT SWITCH TRIPPED 072
HOLD SIGNAL OUTPUT IN AUTO MODE 073
MOTION SERVO COMPLETE SIGNAL LOSS 074
LIFT CAPACITY OVERLOAD 075
SELECTOR POSITION MALFUNCTION 076
MANUAL OVERRIDE ERROR 077
EMERGENCY RECALL IN USE 078
BRAKE TEMPERATURE HIGH 079
LOW AIR PRESSURE 080
EXCESSIVE CONDENSATION IN AIR SUPPLY LINE 081
P-E AIR SIDE CONTAMINATION 082
GROUND FAULT MINUS OPEN 083
LIGHTNING PROTECTION CIRCUITRY INOPERATIVE 084
OPERATION COMMAND ABORT 085
SUPERVISORY INPUT LOW 086
BEARING DISPLACEMENT TRIPPED--CABIN SUPPORT RING 087
EXCESSIVE WOBBLE 088
TIMING CIRCUIT OUT OF CALIBRATION 089
IMPROPER OPERATION SEQUENCE--MANUAL MODE 090
OIL CONTAMINATION 091
ERRATIC COMMUTATION--SELECTOR 092
SIGNAL LOSS--OPTOCOUPLER MASTER SERVO INTERFACE 093
BREAKAWAY FAILURE 094
AMBIENT TEMPERATURE TOO LOW 095
AMBIENT TEMPERATURE TOO HIGH 096
DUTY CYCLE DESIGN LIMIT REACHED 097
CPU INTERNAL CLOCK INTERRUPTED 098
TENSION FOLLOWER NEEDS ADJUSTMENT 099
CABLE SLACK BEYOND DESIGN LIMITS 100
MAIN HUB INTERFACE FAILURE 101
OIL PRESSURE ERRATIC 102
AIR PRESSURE ERRATIC 103
MAIN POWER MONITOR SIGNAL ERRATIC 104
IMPROPER PASSWORD TO DIAGNOSTICS 105
IMPROPER PASSWORD TO MANUAL OPERATION 106
USER NOT IN CURRENT FILE 107
TIME LOG DATA NOT ENTERED PROPERLY 108
SERVO AMPLIFIER GAIN TOO HIGH 109
SERVO AMPLIFIER GAIN TOO LOW 110
SERVO AMPLIFIER GAIN ZERO 111
SERVO AMPLIFIER UNSTABLE 112
SERVO AMPLIFIER FAILURE 113
SERVO AMPLIFIER IN/OUT z INCORRECT 114
SERVO AMPLIFIER BUFFER OUT OF CALIBRATION 115
A.C. RIPPLE PRESENT IN FILTERED SECTION OF D.C. SUPPLY 116
REVERSE ACCUMULATOR BELLOWS FAILURE 117
REVERSE ACCUMULATOR PRESSURE HIGH 118
AIR SWITCH CIRCUIT MALFUNCTION 119
INDUCTION CIRCUITRY INOPERATIVE 120
DYNAMIC CONTROLLER MALFUNCTION 121
COUNTER BALANCE DETECTION SERVO FAILURE 122
COUNTER BALANCE DETECTION SERVO FALSE SIGNAL 123
COUNTER BALANCE DETECTION TRANSDUCER OPEN 124
COUNTER BALANCE DETECTION TRANSDUCER SHORTED 125
DECELERATION SEQUENCER MALFUNCTION 126
SPEED SENSOR FALSE SIGNAL 127
SPEED SENSOR SHORTED 128
SPEED SENSOR OPEN 129
TEMPERATURE SENSOR--AIR--INOPERATIVE 130
TEMPERATURE SENSOR--AIR--BUFFER OUT OF CALIBRATION 131
ACCELEROMETER TRANSDUCER OPEN 132
ACCELEROMETER TRANSDUCER SHORTED 133
ACCELEROMETER TRANSDUCER TEMP HIGH 134
ACCELEROMETER TRANSDUCER SHORTED TO GROUND 135
<<END OF LIST>>
<<TERMINATION OF USER COMMAND>>
