Pro2-A ver 2.01 bios

[heng1028]

I have flashed the 2.01 bios from german site

and i don't have the multiplier below 10

i couldn't get multiplier like 9, 9.5, 8.5....

i have only 10- 12.5 multiplier

does anyone has this problem??

 

[Rong]

I also got it from German WebSite.
And Flashed it.
I got those Multiplier.
No Problem.

Good Luck.

Try it once more.

 

[mlusr]

Though I didn't flashed the 2.01 bios,
my Pro2-A bios didn't have multiplier below 10, too.
How can I get them?

 

[heng1028]

i reflashed the old ver 1.9 bios

i got the multiplier below 10

 

[MassMhz]

I also flashed 2.01,nothing below 10,but i dont need it.Are there any other differences between 2.01 and 1.8,cause i dont see anything worth the flash do you?

 

[RoboTECH]

I believe it sets your default voltage to 1.85v

Very useful for duron overclockers, as they (we) typically need 1.85v or more to hit 1-Gig

The T-Bird's default to a higher voltage naturally than the Duron's do, so 1.85v is a setting that is typically "do-able" on a T-Bird normally.

 

[heng1028]

the default will set to 1.85 if you connected the L7 bridges

 

[L1Trauma]

Do you connect ALL the L7 bridges? Dumb question, I know...

 

[victorwon]

Help NEEDED!!

I just build a new PC as following:
Duron 650
MSI K7TPRO2A
Radeon DDR 64MB
ATI TV Wonder PCI
SB Live! Value
256MB Kingmax PC150
Afreey 8xDvD
Panasonic 8x4x32 CDRW

But I cannot get my Radeon running any 3d games more than 5 seconds!!!
Every time I startup the D3D or Opengl game, the screen locked and system hang.
I have tried to set the AGP Driving Value in the BIOS for DA EA FA CC B8 B6 B7 68 69 70 7A CA BA 66 EE EF DE DF
but no one works!!! AGP 4x is also disabled.

I install the via4in1 drivers 4.25a and 4.26, all new Radeon drivers, support and special. DirectX 8. But result the same. I am nearly crashed these days.

I don't know which to blame, MSI or ATI or VIA? But...

Please help. and by the way how to post a new topic here? I cannot find the post button as described in the forum's help.

Thanks in advance
Victor

 

[Amaretto747]

Go to START choose RUN , type msconfig then go to STARTUP, uncheck ATIGART, reinstall the via 4in1 then you should be okay now. If not, here's a link where you can get some more help.http://www.rage3d.com/forum/forumdi...amp;number=13&DaysPrune=20&LastLogin=

 

[Amaretto747]

To get back the multiplier below 10, just reset the CMOS, look in the manual and there's a jumper in the motherboard that you have to short-circuit, do this with the power off, not on, since that would damage your mobo.

 

[Octoberblue]

L1Trauma: For 1.85 volts yes, you connect all of them. Not sure if you can lower it again in the bios or not. Anand illustrates it here.

 

[heng1028]

i flashed the new bios with the old one

and i got back all the multiplier below 10