- Jun 21, 2005
- 12,040
- 2,256
- 126
Here you go.
Apparently it's stable at 650MHz core and 1000MHz (DDR3 2000) memory. It ran through 3DMark06 without any artifacting. I didn't try to go any higher yet...will try soon.
To overclock I'm using ATITool. It gives much finer control than nTUNE and I can test stability also. The clocks are apprently being set properly because it shows up in nTUNE as the correct clocks. 3DMark06 scores don't go up much. from stock to OCed, I only gained about 5-600 points.
Temps stayed under 70 celcius when overclocked with the fan at 100% and my case opened. With the fan at 100% it is loud so I will not keep it that high. It's idling right now at about 55 celcius with the same conditions as above.
And finally, WOOHOOOOO!!! Hehe had to get that out of my system.
Edit 1: Okay at about 670+MHz it locks up so I'll keep it at 650MHz. And as for the memory, it locks up at about 1060MHz so I'll keep it at 1000MHz. Well...that was some quick testing using ATITool. I suggest anyone OCing to use that instead of nTune.
Edit 2: One thing I found was that for 3DMark06, when I tried to force AA and AF through the control panel...it wasn't being set properly. Only when set from within 3dmark did it work.
Edit 3:
All tests run at 1280x1024 (17inch monitor FTW!!!
)
Fear
All settings maxed...although I don't think soft shadows are working with the AA enabled(this problem has been mentioned before I think).
at stock:
click
OCed to 650/1000:
click
Company of Heroes
All settings maxed (ultra and high settings for everything)
stock:
click
OCed to 650/1000:
click
One thing I noticed was that any settings set from the control panel were not being used in-game so all settings were set in-game.
Apparently it's stable at 650MHz core and 1000MHz (DDR3 2000) memory. It ran through 3DMark06 without any artifacting. I didn't try to go any higher yet...will try soon.
To overclock I'm using ATITool. It gives much finer control than nTUNE and I can test stability also. The clocks are apprently being set properly because it shows up in nTUNE as the correct clocks. 3DMark06 scores don't go up much. from stock to OCed, I only gained about 5-600 points.
Temps stayed under 70 celcius when overclocked with the fan at 100% and my case opened. With the fan at 100% it is loud so I will not keep it that high. It's idling right now at about 55 celcius with the same conditions as above.
And finally, WOOHOOOOO!!! Hehe had to get that out of my system.
Edit 1: Okay at about 670+MHz it locks up so I'll keep it at 650MHz. And as for the memory, it locks up at about 1060MHz so I'll keep it at 1000MHz. Well...that was some quick testing using ATITool. I suggest anyone OCing to use that instead of nTune.
Edit 2: One thing I found was that for 3DMark06, when I tried to force AA and AF through the control panel...it wasn't being set properly. Only when set from within 3dmark did it work.
Edit 3:
All tests run at 1280x1024 (17inch monitor FTW!!!
Fear
All settings maxed...although I don't think soft shadows are working with the AA enabled(this problem has been mentioned before I think).
at stock:
click
OCed to 650/1000:
click
Company of Heroes
All settings maxed (ultra and high settings for everything)
stock:
click
OCed to 650/1000:
click
One thing I noticed was that any settings set from the control panel were not being used in-game so all settings were set in-game.