MSI pt880 with p4 2.8 chip wont boot

raidahs

Member
Feb 6, 2004
42
0
0
Hey i just got a new MSI pt880 motherboard and also a new p4 2.8 chip. everything else im using is pulled out of my old machine. 9800 pro, crucial 512 pc3200 and maxtor 160 hd. my problem is that everything turns on but it wont boot. the cpu fan and video card fan spins. also if i were to pull the ram out it wont have that long beep so im thinking its the cpu or motherboard. so i reinstalled the cpu and hsf again and still nothing is working. what should i do now?
 

johnjkr1

Platinum Member
Jan 10, 2003
2,124
0
0
First, is the computer posting? Boot means that it goes to windows, I am assuming you mean that you see nothing on the screen?

Ok, step one, remove all unnecessary devices (mouse, keyboard, pci cards, usb, etc). Reset the cmos and see if it comes up. If it does not, you have at least narrowed it down to cpu, mb, power supply and vid card. I think it is pretty safe to assume your video card is ok. Have you tried it with your old cpu, if it is a pentium? Have you tried it with only one stick of memory, if you have two?

As for the beeping, do you have a pc speaker installed? (not your normal speakers) You will not hear memory beep codes if you do not have a pcspeaker installed.
 

raidahs

Member
Feb 6, 2004
42
0
0
Well my old pc was a amd so i can t check it so i ll just have to wait til tomorrow and test my cpu on my friends pc. i unplugged all pci cards and nothing is working. gosh i hope its not my cpu. Thanks for the help.
 

raidahs

Member
Feb 6, 2004
42
0
0
Opps What happened was that i was messing with the wires and the 12v atx came loose. So im pretty sure my cpu chip is fine. Now i can post and see the msi screen but after 10 seconds it shuts down completely. If i were to turn it on again it will stay on for 2 seconds only? Any help or suggestions?
 

johnjkr1

Platinum Member
Jan 10, 2003
2,124
0
0
If it is shutting down immediately like that, you need to check your heatsink. It sounds like it is not installed properly.
 

raidahs

Member
Feb 6, 2004
42
0
0
i m starting to think that my power supply is too weak. its 400watts max. i also have to double check my heatsink fan tomorrow if its place properly. other then that im ready to rma this board to newegg.
 

johnjkr1

Platinum Member
Jan 10, 2003
2,124
0
0
agreed, 400 should be plenty. I will almost guarantee you that it is not the motherboard causing it to shut down.
 

Cr0nJ0b

Golden Member
Apr 13, 2004
1,141
29
91
meettomy.site
400W is more than you need probably. I have 4 HDs 2 DVDs, a power sucking Vid card, USB and partige in a pear tree and I'm fine with power...

I would check the heatsink as suggested earlier.

Memory mismatch will do this too, in some cases.

If you can get to the setup screen then you have past step one...next try to boot from a CD, then HD...see where it starts to freak out...if you have issues when it's booting to HD, then you probably have a bad drive or your IDE cables are wacked.

 

raidahs

Member
Feb 6, 2004
42
0
0
found out my problem. i needed to install the new bios because its not compatible with the 2.8e. Im not sure why but thats a problem. so basically i had to get my buddies chip and install xp on my hd. now i need to flash my bios but i dont know how to. i cant stand these cheap msi boards. arghhhhh any help will greatly be appericated on how to flash bios
 

raidahs

Member
Feb 6, 2004
42
0
0
Thanks a million John. I finally got it up and running smoothly with this board, However im running my friends p4 2.6 northwood chip. I ll get my chip back tomorrow. Anyways im so greatful to have finally found the live update that msi has. I was ready to trash this mb but now it seems like iit has all these fun features on it. So what I learn from this board is that you must flash the bios and i had a really hard time flashing without the live update by msi. My lesson from this: dont by a prescott chip and this msi board because its going to be a pain in the butt unless they flash all the boards for you. Not worth the trouble imo.

my next step now is trying to install a pci ata raid controller that i bought on ebay. Thanks once again for the help and feel free if you want to the do's and dont's of raid 0. :)
 

raidahs

Member
Feb 6, 2004
42
0
0
gosh now my pc wont detect my second hd.it comes out on the device manager but not on my computer. could it be that both are 160g from maxtor? argh what to do now. this new pc is a pain in the booty.
 

johnjkr1

Platinum Member
Jan 10, 2003
2,124
0
0
Simple, you have to format the drive for windows to be able to see it. Go into control panel, open administrative tools, go to computer management, then choose disk management.

Also, I hope you installed service pack 1 and the proper chipset drivers for your motherboard.
 

imported_Phil

Diamond Member
Feb 10, 2001
9,837
0
0
If you can find a site with decent download speed, go get AutoPatcher XP as well; it applies all the post-Service Pack 1 updates and a whole load more goodies in one go without rebooting or having to use Windows Update.

The speed increase that the various registry tweaks apply is quite noticeable, and there's some neat screensavers too.