• We’re currently investigating an issue related to the forum theme and styling that is impacting page layout and visual formatting. The problem has been identified, and we are actively working on a resolution. There is no impact to user data or functionality, this is strictly a front-end display issue. We’ll post an update once the fix has been deployed. Thanks for your patience while we get this sorted.

I am an idiot

GasX

GasX

Lifer
I finally built my new PC last night. I got everything but the sound card, but I couldn't wait any longer. I got the thing running, set-up the BIOS, formatted the HD, installed Windows 98 and installed the various drivers for Geforce, mouse, etc... I even installed some software. Right before going to bed, I decided to OC the damn thing.

I jacked up the FSB from 100 to 120 and rebooted.

DOH!

It powers up, the drives spin, but nothing happens. The monitor stays blank, so maybe the vid card is an issue. Never the less it doesn't get far enough for me to get back into the BIOS and fix the settings.

How do I get it back>?

plz hlp!


Duron 600 w/ stock HSF
Asus a7V
128MB PC143 Mosel Vitelic RAM
WD 30GB HD
Jaton GeForce2 MX
 
i'm sure that some motherboards have dip switches on them that let you reset the fbs to default just for situations like this one
read your mobo manual should tell you if you have them
 
there is a Jumper for CLEAR CMOS you need to set that, reboot, then turn it off set it back and you're in.
In order to get my computer to boot up with 133Mhz Bus (266), i had to connect the L6 briges on the CPU with a conductive pen to lower the default multiplier, I also connected the L7 bridges to increase the power-on voltage to 1.85. This allows your computer to boot up into Bios then the Bios will take over and adjust it to the settings you choose.

-Matt
 
Hmm, now you say you jacked up the FSB. Did you do anything to the dipswitches? With my A7V, if I change something in the BIOS and the system cannot POST as a result of that, then it will revert the BIOS to "safe" settings the next time I try to boot.

So for example, let's say I jack my FSB up to 120MHz and exit the BIOS. The system attempts to POST at 120MHz, but of course that doesn't work. Upon the next boot, it would revert to a 100MHz FSB and automatically show the BIOS configuration menu.

Maybe your system cannot even get that far, due to the fact that your RAM is now trying to run at 133MHz + 20MHz = 155MHz. That's just a guess. But if you messed with the dipswitches also, try putting them back to their default positions first. If that doesn't work, find the two solder points near the CMOS battery and short them with a bit of wire, perhaps a paperclip. Look in the manual for details on that.
 
Use the clear CMOS jummper,and next time when you overclock DONT go for the kill the first time.You may get it stable at 105mhz to 110mhz.I have the same problem if I set the fsb or the multiplier too high.
 
Do a little research as well before overclocking. Your using the KT133 chipset which is totally unstable beyond 110FSB, which of course would lockup in the BIOS.
 
Thanks to all. I will take this under advisement when I get home.

I knew that going to 120 would probably not work, but I'm aggressive by nature and hoped I'd at least get it to post...
 
don't feel bad, your not alone.. i did the exact same thing last night ( i posted about it in another thread i started )..

Anyone here successfully overclocked an Asus A7M266? im using a 1.2 200fsb that i would like to get to 266..

thanks
 
I've done something similar. Beer and working on computers don't mix. I've learned to wait and have the beer once I'm done. Clearing the CMOS does the trick.
 
MORE POWER! - exactly right.

When I get home tonight, I am going to get it back online and start over.

Tomorrow the world will know how far an unlocked Duron 600 (stock HSF) will go in an unmodified Enlight 7237 on an Asus A7V.
 
Always inch up on the limits. 2 MHz at a time is plenty for me. You'll see it get unstable before you can hurt anything.
 


<< I've done something similar. Beer and working on computers don't mix. I've learned to wait and have the beer once I'm done. Clearing the CMOS does the trick. >>



LOL

I don't know how many times I can recall drinking, and waking up the next morning to have my computer just totally screwed.. haha, its all good.
 
Well, I got it to post at 1017, but Windows was filled with problems. I am absolutely rock solid stable @ 875.

Duron 600 Stock HSF
Enlight 7237
1 case fan
1 power supply fan

When the CardCooler XT, Antec 80mm, &amp; 2CoolPC Plus arrive I will try again.

Next step - better HSF
 
Right now I have my 650 Duron @ 850 (8.5x100). Before I settled on this, I was jacking it up with the FSB, but I found that if I tried to go up too fast ...it would just lock, so I started going up a step at a time ...finally getting it to 107x8=856.
I may go back to fiddlin' with the FSB again later. Next I will probably just try for 900 (9x100)
Neos

MSI Pro 2
128 Mg. PC133 Micron
Duron 650@850
FOB32 with cheap grease.
 
Clear the CMOS either by taking out the battery for a few minutes, or using the jumper. Or try holding down the INSERT key when you reboot.
 
You must log in or register to reply here.

TRENDING THREADS

Back
Top