bnc refresh rate problem

[NEOo]

hi

i have the iiyama vision master pro 21
and the ati 9800pro
connected with bnc

so its without dcc.........


and i cant get the refresh rate higher than 60

the drivers i tryed are 4.11 4.12 and 5.1 with and without ccc.
i also tryed several refresh forcers butt this does'nt help a thing

can someone help me with this thing?

 

[Mem]

I had that problem with CCC on 4.11s however without the CCC it`s fine(using 5.1s in BNC mode),check your monitor tab is set higher then 60Hz,also install your monitor drivers,btw you can set the rerfesh for 3D as well ,go to ATI display tab and click on the monitor button icon ,in there you see "refresh rate over ride" box for 3D gaming.

 

[NEOo]

i've installed the right driver for the monitor.
the refresh rate i tryed 72 85 and 100 all stays on 60
and the display tab doenst have the monitor, because the bnc is without dcc.

 

[Mem]

and the display tab doenst have the monitor, because the bnc is without dcc.

Did you reboot?..I always reboot after,the way I do it is install ATI drivers using express installation,reboot then install monitor drivers at desktop and reboot again then setup the refresh rate etc.....

You might consider trying Driver cleaner in safe mode as well,link. ,instructions are included in the readme file but basically you uninstall your ATI drivers,boot into safe mode run Driver Cleaner and select "ATI" for cleaning,when it`s finished ,boot back to normal desktop and install latest ATI drivers without the new CCC .




ATI driver

link for 5.1s.

Also in the monitor tab make sure "hide modes that this monitor can`t display" IS NOT TICKED.

 

[NEOo]

ok im going to try the cleaner thing.

and i always reboot...

 

[Mem]

and the display tab doenst have the monitor, because the bnc is without dcc.

?...There`ll be a monitor pic like in this link (bottom pic) just click where it says "monitor" where you see 4 monitor pics in the screenshot,so first one,this`ll bring up a new section ,so in there`ll you see 4 tabs,first is attribrutes tab,I set max refresh rate to 100Hz on mine and refresh over ride at 85Hz for gaming.

 

[NEOo]

doenst help anything.... installed 5.1 again without ccc.

set to refresh to 85 and 100 and nothing.....


bnc doenst support dcc info. so i dont have the monitor thing in displays

 

[Mem]

You do have the ATI control panel installed?,I don`t mean the new CCC.

Did you check montior tab,"hide modes that this monitor can`t display" is not ticked,then select something higher the 60Hz.

 

[NEOo]

yep

 

[NEOo]

yep and i have the display tab i just dont have the monitor in it...

 

[Mem]

yep and i have the display tab i just dont have the monitor in it...

So what do you have in your display tab?..It should be similar to this,bottom pic.

 

[NEOo]

yeh i know i just have nothing in it, just gray like that YPbPR thing on the pic.

 

[Mem]

Does it have a X as well like in the same pic,hmmm try using a normal VGA cable see if that works

 

[NEOo]

its the same like it the pic of the YPbPr
cant use normal vga for this monitor

 

[Mem]

Running out of ideas,but try installing your monitor driver again,reason I wanted you to try a normal VGA cable is to see if that works above 60Hz,trying to see if it`s a BNC specific or general problem with your monitor.

 

[NEOo]

oke thnx for the try.....

is there maybe someone elce who knows a possible sollution?

 

[NEOo]

help?

 

[alexandernevsky]

have you tried:


http://www.pagehosting.co.uk/rf/


+ if that doesnt do it go for a google search I think its a well known issue with windows.

 

[NEOo]

yeh is tryed that refresh forcer and it didnt worked.

and i tryed searching on google with bnc refresh rate and i cant find the awnser

 

[Mem]

Tried RefreshLock (note this is not RefreshForce),you have to download RL from top left of the webpage.

Do you have more then one monitor linked to your ATI card?

 

[NEOo]

i tryed that one..

no only that 21" iiyama monitor

 

[NEOo]

?

 

[Mem]

I presume you are using XP?...I would try the full Driver Cleaner cleanup in safe mode,that`s run cab cleaner which is in tools menu then run Driver Cleaner last for "ATi",btw make sure you use the ATI uninstall utility in control panel(add/uninstall icon) to remove the ATI drivers first before going into safe mode,also make sure CCC is removed as well if you have that installed.

 

[NEOo]

yeh im using xp sp2.

i've done all of that.
and reinstalled 5.1 without ccc.

and still nothing.

 

[Mem]

Tried both ports on your ATI card?..use the DVI-VGA adaptor for the DVI port.