Hi
I need some help to get my system stable
I would like to run the CPU at 3.66GHz and the mem's as fast as possible
But I can't get the system to be stable with these settings I get alot of BSOD
"Page Fault in Non Paged Area"
If I start running Prime95 after the computer has been turned off for awile it's stable for 30 min then it starts to crash and then the system is unstable untill it has been cool down.
The same thing happands even if I run FSB att 1333 and Multiple 9X (3Hz) it can take an hour before the BSOD starts here.
The only thing I can do to make the system "totaly" stable is lower the FSB to 1066, then the system works just fine.
So I need so help to get my system stable. any tips what to do?
Thx guys!
Config:
MB: ASUS Striker II Formula (BIOS 1001)
CPU: QX9650 (Runing at 3.66GHz)
MEM: 4 x 1GB Dominator PC2-8500 (1066MHz, 5-5-5-15-2T, 2.15V)
HDD: 2 x RaptorX (RAID 0), 2 x WD 750GB
Cooling: ZALMAN Water cooling, Reserator XT
MAIN
Legacy Diskette A: ---------------------------------[1,44 3,5 IN]
Primary IDE Master---------------------------------[None]
Primary IDE SLAVE---------------------------------[None]
SATA 3-----------------------------------------------[WDC WD750]
SATA 4-----------------------------------------------[WDC WD750]
SATA 5-----------------------------------------------[TSS TCOUG]
SATA6------------------------------------------------[TSS TCOUG]
HDD SMART Monitoring-----------------------------[Enabled]
Primary IDE MASTER/SLAVE (Main Sub menu)
PIO Mode-------------------------------------------[Auto]
UDMA-----------------------------------------------[Auto]
Primary IDE Master/Slave------------------------[None]
Extreme Tweaker
Loadline Calibration------------------------------[Disabled]
NVIDIA GPU EX-----------------------------------[Enabled]
SLI-Ready Memory-------------------------------[Disbaled]
Voltiminder LED-----------------------------------[ON]
CPU LED Selection--------------------------------[CPU Volt]
NB LED Selection----------------------------------[NB Volt]
SB LED Selection----------------------------------[SB Volt]
ROG Logo------------------------------------------[Enabled]
ES Selection---------------------------------------[Disabled]
System Clocks (Extreme Tweaker Sub menu)
PCIEX16_3 Frequency (MHz)------------------[100]
PCIEX16_1 2 Frequency (MHz)----------------[100]
SPP<->MCP Ref Clock, Mhz-------------------[Auto]
FSB & Memory Config (Extreme Tweaker Sub menu)
FSB ? Memory Clock Mode---------------------[Unlinked]
FSB (QDR ), MHz--------------------------------[1333]
MEM (DDR, MHz---------------------------------[800]
Memory Timing Settings (Extreme Tweaker Sub menu)
tCL---------------------------------------------------[5]
tRCD-------------------------------------------------[5]
tRP---------------------------------------------------[5]
tRAS-------------------------------------------------[15]
Commands Per Clock (CMD)---------------------[2 clock]
**Advanced Memory settings**
tRRD-------------------------------------------------[AUTO]
tRC---------------------------------------------------[AUTO]
tWR---------------------------------------------------[AUTO]
tWTR-------------------------------------------------[AUTO]
tREF--------------------------------------------------[AUTO]
tRD---------------------------------------------------[AUTO]
tRFC--------------------------------------------------[AUTO]
Async Latency---------------------------------------[AUTO]
Spred Spectrum Control (Extreme Tweaker Sub menu)
CPU Spread Spectrum---------------------------[Disabled]
SATA Spread Spectrum--------------------------[Disabled]
LDT Spread Spectrum----------------------------[Disabled]
Over Voltage (Extreme Tweaker Sub menu)
CPU Voltage----------------------------------------[1,293751]
CPU PLL Voltage------------------------------------[Auto]]
CPU VTT Voltage-----------------------------------[Auto]]
Memory Voltage------------------------------------[2,20]
NB Core Voltage------------------------------------[Auto]
SB Core Voltage------------------------------------[Auto]
1,2 HT Voltage--------------------------------------[Auto]
Bridge Core Voltage--------------------------------[Auto]
CPU GTL_REF Ratio---------------------------------[Auto]
NB GTL_REF Ratio-----------------------------------[Auto]
DDR II Controller Ref Voltage---------------------[Auto]
DDR II Channel A Ref Voltage---------------------[Auto]
DDR II Channel B Ref Voltage----------------------[Auto]
Over Clocking (Extreme Tweaker Sub menu)
CPU Internal Thermal Control--------------------[Disabled]
Limit CPU MaxVal----------------------------------[Disabled]
Enhanced C1 (C1E)--------------------------------[Disabled]
Execute Disable Bit--------------------------------[Enabled]
Virtualization Technology -------------------------[Enabled]
CPU Muliplier---------------------------------------[11 X]
CPU N/2 Ratio--------------------------------------[Disabled]
Enhanced Intel Speed Tech-----------------------[Disbaled]
LDT Frequency--------------------------------------[5 X]
CPU CORE 2-----------------------------------------[Enabled]
CPU CORE 3-----------------------------------------[Enabled]
CPU CORE 4-----------------------------------------[Enabled]
AI NET 2 (Advanced Sub menu)
POST Check LAN Cable--------------------------[Disabled]
POST Check LAN2 Cable-------------------------[Disabled]
PCIPnp (Advanced Sub menu)
Plug & Play O/S------------------------------------[Yes]
Primary Display Adapter-------------------------[PCI-E]
Onboard Device Configuration (Advanced Sub menu)
HD Audio--------------------------------------------[Disabled]
Onboard 1st nVidia LAN----------------------------[Enabled]
Onboard 2st nVidia LAN---------------------------[Enabled]
Onboard LAN Boot ROM---------------------------[Disabled]
Onboard 1394--------------------------------------[Enabled]
LCD Poster Off-------------------------------------[Enabled]
LCD Poster Backlight------------------------------[Enabled]
LCD Poster Mode----------------------------------[Current Time]
IDE Functions (Advanced Sub menu)
OnChip Channel0----------------------------------[Enabled]
IDE DMA transfer access------------------------[Enabled]
IDE Prefetch Mode--------------------------------[Enabled]
Serial-ATA Configuration (Advanced Sub menu)
Serial-ATA Controller-----------------------------[Enabled]
RAID Enabled---------------------------------------[Enabled]
SATA1 RAID ----------------------------------------[Enabled]
SATA2 RAID ----------------------------------------[Enabled]
SATA3 RAID ----------------------------------------[Disabled]
SATA4 RAID ----------------------------------------[Disabled]
SATA5 RAID ----------------------------------------[Disabled]
SATA6 RAID ----------------------------------------[Disabled]
USB Configuration (Advanced Sub menu)
USB Controller-------------------------------------[Enabled]
USB Leagacy support-----------------------------[Enabled]
USB 2.0 Controller --------------------------------[Enabled]
Power
ACPI Suspend Type-------------------------------[S1&S3]
APM Configuration (Power Sub menu)
Restore on AC Power Loss-----------------------[Power-Off]
PWR Button < 4 secs-----------------------------[Instant-Off]
Power on By PCI/PCIE Devices------------------[Disabled]
USB Resume from S5-----------------------------[Disbaled]
Power On By RTC Alarm--------------------------[Disabled]
HPET Support---------------------------------------[Enabled]
Power On By PS/2 Keyboard---------------------[Disabled]
Hardware Monitor (Power Sub menu)
CPU Fan Speed Warning-------------------------[Disabled]
Temperature Monitor (Power Sub menu)
NB Overheat Protection-------------------------[90]
SB Overheat Protection--------------------------[90]
Boot Device Prioity (Boot Sub menu)
1st Boot Device------------------------------------[CDROM]
2st Boot Device------------------------------------[Hard Disk]
3st Boot Device------------------------------------[Disabled]
4st Boot Device------------------------------------[Disabled]
Hard Disk Drives (Boot Sub menu)
1. SCSI-0 : NVIDIA STRIPE 297,47G
2. WDC WD750
Boot Settings Configuration (Boot Sub menu)
Case Open Warning-------------------------------[Enabled]
Quick Boot------------------------------------------[Enabled]
Boot up Floppy Seek-------------------------------[Disabled]
Bootup Num-Lock----------------------------------[Enabled]
OS Select For DRAM > 64MB---------------------[Non-OS2]
Full Screen LOGO----------------------------------[Enabled]
BIOS Wallpaper------------------------------------[25%]
Halt On----------------------------------------------[All Errors]
I need some help to get my system stable
I would like to run the CPU at 3.66GHz and the mem's as fast as possible
But I can't get the system to be stable with these settings I get alot of BSOD
"Page Fault in Non Paged Area"
If I start running Prime95 after the computer has been turned off for awile it's stable for 30 min then it starts to crash and then the system is unstable untill it has been cool down.
The same thing happands even if I run FSB att 1333 and Multiple 9X (3Hz) it can take an hour before the BSOD starts here.
The only thing I can do to make the system "totaly" stable is lower the FSB to 1066, then the system works just fine.
So I need so help to get my system stable. any tips what to do?
Thx guys!
Config:
MB: ASUS Striker II Formula (BIOS 1001)
CPU: QX9650 (Runing at 3.66GHz)
MEM: 4 x 1GB Dominator PC2-8500 (1066MHz, 5-5-5-15-2T, 2.15V)
HDD: 2 x RaptorX (RAID 0), 2 x WD 750GB
Cooling: ZALMAN Water cooling, Reserator XT
MAIN
Legacy Diskette A: ---------------------------------[1,44 3,5 IN]
Primary IDE Master---------------------------------[None]
Primary IDE SLAVE---------------------------------[None]
SATA 3-----------------------------------------------[WDC WD750]
SATA 4-----------------------------------------------[WDC WD750]
SATA 5-----------------------------------------------[TSS TCOUG]
SATA6------------------------------------------------[TSS TCOUG]
HDD SMART Monitoring-----------------------------[Enabled]
Primary IDE MASTER/SLAVE (Main Sub menu)
PIO Mode-------------------------------------------[Auto]
UDMA-----------------------------------------------[Auto]
Primary IDE Master/Slave------------------------[None]
Extreme Tweaker
Loadline Calibration------------------------------[Disabled]
NVIDIA GPU EX-----------------------------------[Enabled]
SLI-Ready Memory-------------------------------[Disbaled]
Voltiminder LED-----------------------------------[ON]
CPU LED Selection--------------------------------[CPU Volt]
NB LED Selection----------------------------------[NB Volt]
SB LED Selection----------------------------------[SB Volt]
ROG Logo------------------------------------------[Enabled]
ES Selection---------------------------------------[Disabled]
System Clocks (Extreme Tweaker Sub menu)
PCIEX16_3 Frequency (MHz)------------------[100]
PCIEX16_1 2 Frequency (MHz)----------------[100]
SPP<->MCP Ref Clock, Mhz-------------------[Auto]
FSB & Memory Config (Extreme Tweaker Sub menu)
FSB ? Memory Clock Mode---------------------[Unlinked]
FSB (QDR ), MHz--------------------------------[1333]
MEM (DDR, MHz---------------------------------[800]
Memory Timing Settings (Extreme Tweaker Sub menu)
tCL---------------------------------------------------[5]
tRCD-------------------------------------------------[5]
tRP---------------------------------------------------[5]
tRAS-------------------------------------------------[15]
Commands Per Clock (CMD)---------------------[2 clock]
**Advanced Memory settings**
tRRD-------------------------------------------------[AUTO]
tRC---------------------------------------------------[AUTO]
tWR---------------------------------------------------[AUTO]
tWTR-------------------------------------------------[AUTO]
tREF--------------------------------------------------[AUTO]
tRD---------------------------------------------------[AUTO]
tRFC--------------------------------------------------[AUTO]
Async Latency---------------------------------------[AUTO]
Spred Spectrum Control (Extreme Tweaker Sub menu)
CPU Spread Spectrum---------------------------[Disabled]
SATA Spread Spectrum--------------------------[Disabled]
LDT Spread Spectrum----------------------------[Disabled]
Over Voltage (Extreme Tweaker Sub menu)
CPU Voltage----------------------------------------[1,293751]
CPU PLL Voltage------------------------------------[Auto]]
CPU VTT Voltage-----------------------------------[Auto]]
Memory Voltage------------------------------------[2,20]
NB Core Voltage------------------------------------[Auto]
SB Core Voltage------------------------------------[Auto]
1,2 HT Voltage--------------------------------------[Auto]
Bridge Core Voltage--------------------------------[Auto]
CPU GTL_REF Ratio---------------------------------[Auto]
NB GTL_REF Ratio-----------------------------------[Auto]
DDR II Controller Ref Voltage---------------------[Auto]
DDR II Channel A Ref Voltage---------------------[Auto]
DDR II Channel B Ref Voltage----------------------[Auto]
Over Clocking (Extreme Tweaker Sub menu)
CPU Internal Thermal Control--------------------[Disabled]
Limit CPU MaxVal----------------------------------[Disabled]
Enhanced C1 (C1E)--------------------------------[Disabled]
Execute Disable Bit--------------------------------[Enabled]
Virtualization Technology -------------------------[Enabled]
CPU Muliplier---------------------------------------[11 X]
CPU N/2 Ratio--------------------------------------[Disabled]
Enhanced Intel Speed Tech-----------------------[Disbaled]
LDT Frequency--------------------------------------[5 X]
CPU CORE 2-----------------------------------------[Enabled]
CPU CORE 3-----------------------------------------[Enabled]
CPU CORE 4-----------------------------------------[Enabled]
AI NET 2 (Advanced Sub menu)
POST Check LAN Cable--------------------------[Disabled]
POST Check LAN2 Cable-------------------------[Disabled]
PCIPnp (Advanced Sub menu)
Plug & Play O/S------------------------------------[Yes]
Primary Display Adapter-------------------------[PCI-E]
Onboard Device Configuration (Advanced Sub menu)
HD Audio--------------------------------------------[Disabled]
Onboard 1st nVidia LAN----------------------------[Enabled]
Onboard 2st nVidia LAN---------------------------[Enabled]
Onboard LAN Boot ROM---------------------------[Disabled]
Onboard 1394--------------------------------------[Enabled]
LCD Poster Off-------------------------------------[Enabled]
LCD Poster Backlight------------------------------[Enabled]
LCD Poster Mode----------------------------------[Current Time]
IDE Functions (Advanced Sub menu)
OnChip Channel0----------------------------------[Enabled]
IDE DMA transfer access------------------------[Enabled]
IDE Prefetch Mode--------------------------------[Enabled]
Serial-ATA Configuration (Advanced Sub menu)
Serial-ATA Controller-----------------------------[Enabled]
RAID Enabled---------------------------------------[Enabled]
SATA1 RAID ----------------------------------------[Enabled]
SATA2 RAID ----------------------------------------[Enabled]
SATA3 RAID ----------------------------------------[Disabled]
SATA4 RAID ----------------------------------------[Disabled]
SATA5 RAID ----------------------------------------[Disabled]
SATA6 RAID ----------------------------------------[Disabled]
USB Configuration (Advanced Sub menu)
USB Controller-------------------------------------[Enabled]
USB Leagacy support-----------------------------[Enabled]
USB 2.0 Controller --------------------------------[Enabled]
Power
ACPI Suspend Type-------------------------------[S1&S3]
APM Configuration (Power Sub menu)
Restore on AC Power Loss-----------------------[Power-Off]
PWR Button < 4 secs-----------------------------[Instant-Off]
Power on By PCI/PCIE Devices------------------[Disabled]
USB Resume from S5-----------------------------[Disbaled]
Power On By RTC Alarm--------------------------[Disabled]
HPET Support---------------------------------------[Enabled]
Power On By PS/2 Keyboard---------------------[Disabled]
Hardware Monitor (Power Sub menu)
CPU Fan Speed Warning-------------------------[Disabled]
Temperature Monitor (Power Sub menu)
NB Overheat Protection-------------------------[90]
SB Overheat Protection--------------------------[90]
Boot Device Prioity (Boot Sub menu)
1st Boot Device------------------------------------[CDROM]
2st Boot Device------------------------------------[Hard Disk]
3st Boot Device------------------------------------[Disabled]
4st Boot Device------------------------------------[Disabled]
Hard Disk Drives (Boot Sub menu)
1. SCSI-0 : NVIDIA STRIPE 297,47G
2. WDC WD750
Boot Settings Configuration (Boot Sub menu)
Case Open Warning-------------------------------[Enabled]
Quick Boot------------------------------------------[Enabled]
Boot up Floppy Seek-------------------------------[Disabled]
Bootup Num-Lock----------------------------------[Enabled]
OS Select For DRAM > 64MB---------------------[Non-OS2]
Full Screen LOGO----------------------------------[Enabled]
BIOS Wallpaper------------------------------------[25%]
Halt On----------------------------------------------[All Errors]
Facebook
Twitter