Anyone have the DLT3C JIUHB 0319 1700+ from SVC?

[GRagland]

If you got the DLT3C (1.5v) JIUHB 0319 1700+ from SVC then post your overclocking results. I am interested in getting this chip.

 

[soja]

I have one sitting on my desk calling at me right now. Still backing up etc... I'll let you know how it does asap.

 

[adeno]

Yep, I got one of those.. Running it at 11.5 x 208 MHz for 2.40 GHz at ~1.8v. In the bios I have it set at 1.775v, but the 8RDA+ overvolts. Couldn't get it any higher than 2.4 GHz.

 

[Corporate Thug]

Originally posted by: adeno
Yep, I got one of those.. Running it at 11.5 x 208 MHz for 2.40 GHz at ~1.8v. In the bios I have it set at 1.775v, but the 8RDA+ overvolts. Couldn't get it any higher than 2.4 GHz.

what kind of cooling and what kind of temps

 

[Naruto]

Originally posted by: adeno
Yep, I got one of those.. Running it at 11.5 x 208 MHz for 2.40 GHz at ~1.8v. In the bios I have it set at 1.775v, but the 8RDA+ overvolts. Couldn't get it any higher than 2.4 GHz.

Is that the 0307, 0308, or the new 0319? Big difference between the first two and latter.

 

[adeno]

I have the 0319. As for temps, my 8RDA+ is an older one and doesn't read very accurately (at least that's what I think).. at full load, mbm reports 34-35c. I'm using an SLK-700 + TMD fan (the louder 38db one).

 

[Ilmater]

Originally posted by: soja
I have one sitting on my desk calling at me right now. Still backing up etc... I'll let you know how it does asap.

Ditto. I've got a new video card coming as well, and I'm going to get that set up and overclock it (since I have a stable overclock on my current processor) before I delve into the 0319. I'm ready to go with this thing.

I've been getting bad overclocking results previously, so I'm excited to see how well this 1700+ does compared to my last two.

 

[Polar2002]

I have one and it is running at 2400=12.5x192 @ 1.775v with sk-7 h/s and corsair xms pc3200 2-5-2-2-2. My mb is an old Epox w/kt333 and my video card does not like going higher. Need a lock agp/pci like nforce2.

 

[GRagland]

whats a safe vcore on these chips? im thinking that 1.8v is a little high.

 

[soja]

Finally got my setup up and running. This is a DLT3C (1.5v) JIUHB 0319 from SVC. At 176x12.5 = 2200~ prime failed. So far prime has been running fine at 170x12.5=2125 @ default vcore. I'm not going to bump the voltage just yet because my sk7 w/ 39cfm sunon isn't doing that well. I'm pushing 60c as we speak. I might pick up a smartfan2 and see how far this thing can go. Today is a warm day in Cali, I fear for tomorrow :Q

 

[Syndicate]

I am 'only' running at 2300MHZ =(. 11.5 X 200FSB. Nforce 2. 1.70v on Sk7+92MM 50CFM. 0308.

 

[Ilmater]

I finally got mine in, and it's nothing short of great. 2375MHz (12.5*190) @ 1.775V. I had it at 1.75V, but it had an error in Prime95 after a few hours. I'm pretty sure I'm stable as a rock now. Temps are 48C idle and 52C load w/ Swiftech MCX462+ and a Panaflo 92mm H1A.

The only thing I'm not so happy about is the fact that I could get my board to run any higher than 8.5*200, but any multi higher, no matter how high the Vcore, wouldn't run stably. Note that this happened with my last 1700+ as well, so this is not unique to the SVC proc. So, I lowered the FSB and good things abounded.