• We’re currently investigating an issue related to the forum theme and styling that is impacting page layout and visual formatting. The problem has been identified, and we are actively working on a resolution. There is no impact to user data or functionality, this is strictly a front-end display issue. We’ll post an update once the fix has been deployed. Thanks for your patience while we get this sorted.

Air Conditioning is broken in home

Page 2 - Seeking answers? Join the AnandTech community: where nearly half-a-million members share solutions and discuss the latest tech.
Originally posted by: Xanis
Originally posted by: spidey07
Originally posted by: Rubycon
I'd be willing to bet if you grabbed the fan blades and pulled up and down there's probably a good 1/2" of play there!

They're actually very stable in their rotational plane and the vertical. Blades rotate on the horizontal plane from the cylinder of coils on the vertical plane.

///---motor---///

I'm half tempted to do this myself now. I could just pull the motor and service it! Or just replace it. But the cap is probably elsewhere?

I kinda feel like you might want to leave this to a pro. 😛

If I don't post an update by tomorrow evening, post an obit.

thanks in advance
 
Originally posted by: Rubycon
Tug on the shaft to see how much play you have. If it's more than half the diameter of the shaft it's pretty shot. You can oil it up so it spins freely but don't expect this to be a long term repair. Is this a heat pump or AC unit? 9 years of heat pump use is rather tall.

No heat pump, AC unit. I'm confident I can at least yank the power to this unit (switchbox next to it) and at least pull/inspect the fan motor. It's VERY accessible. Hell, the fan can't start as it is, what danger could there be?
😀
 
Originally posted by: Xanis
must... resist... jokes....

Tugging on an eight inch long shaft with twin ball bearings hanging below? Yeah I should've been an HVAC mechanic! :laugh:
 
Originally posted by: Rubycon
Originally posted by: Xanis
must... resist... jokes....

Tugging on an eight inch long shaft with twin ball bearings hanging below? Yeah I should've been an HVAC mechanic! :laugh:

I rock the roller bearings baby.

'cause, you know...that's just how I roll*

*I claim no responsibility for the lameness of this post

 
Originally posted by: spidey07
Originally posted by: Xanis
Originally posted by: spidey07
Originally posted by: Rubycon
I'd be willing to bet if you grabbed the fan blades and pulled up and down there's probably a good 1/2" of play there!

They're actually very stable in their rotational plane and the vertical. Blades rotate on the horizontal plane from the cylinder of coils on the vertical plane.

///---motor---///

I'm half tempted to do this myself now. I could just pull the motor and service it! Or just replace it. But the cap is probably elsewhere?

I kinda feel like you might want to leave this to a pro. 😛

If I don't post an update by tomorrow evening, post an obit.

thanks in advance

no problem brah, i got your back.
 
I just had one of our units repaired the other day (Zone 2). Everything was running but there was hot air coming out. Turns out the capacitor was blown. This unit has been repaired so many times and every 6 - 9 months something else goes wrong. Certainly cheaper than buying a new unit but no air in the summer is not much fun. Good thing our first zone never breaks so we can always keep cool on the first floor.
 
Bearings and Capacitor is a good place to start.

Another common problem is a pressure switch on a tube that comes out of the compressor. It's purpose is to turn on and off the outside blower motor to keep the condensor cool. If it is bad, you can short the wires that lead to it out. That way, the blower motor will come on every time the compressor comes on. If that is it, it will keep it running until a service guy can come (saving emergency charges). Ive even run some units like that for relitively long periods of time.

That switch has to be replaced by an AC tech because the coolant has to be drained, a tee installed and it has to be recharged.
 
Repair guy just left. Worn motor and the bearings are sealed. Capacitor tested fine - it used a single housing that had two capacitors in it, one for compressor and another for fan.

He was really good, added a separate capacitor just for the fan, checked and adjusted coolant, something called head pressure and cleaned it out. 324 bucks, not too bad considering got a checkup as well and 2+ hours of labor.
 
Originally posted by: spidey07
Originally posted by: Rubycon
CFM (Condenser Fan Motor) should have been replaced IMO.

😕
It was. That's what was bad.

Ok by your latest update it appeared that it was not replaced. Btw they call it refrigerant. 😉
 
Originally posted by: spidey07
Repair guy just left. Worn motor and the bearings are sealed. Capacitor tested fine - it used a single housing that had two capacitors in it, one for compressor and another for fan.

He was really good, added a separate capacitor just for the fan, checked and adjusted coolant, something called head pressure and cleaned it out. 324 bucks, not too bad considering got a checkup as well and 2+ hours of labor.

Time to celebrate with a t-shirt! 😛
 
Originally posted by: YOyoYOhowsDAjello
Originally posted by: spidey07
Repair guy just left. Worn motor and the bearings are sealed. Capacitor tested fine - it used a single housing that had two capacitors in it, one for compressor and another for fan.

He was really good, added a separate capacitor just for the fan, checked and adjusted coolant, something called head pressure and cleaned it out. 324 bucks, not too bad considering got a checkup as well and 2+ hours of labor.

Time to celebrate with a t-shirt! 😛

I told him to check for mice and this is the look I got in return...
😕
 
Back
Top