Search results

  1. M

    Trying to start a gaming community

    Hey everyone I'm trying to start up a friendly gaming community. It's not a clan, its just going to be a place where people can talk about PC games and what not. I have a ventrilo server up so people can use to talk with each other instead of typing while in game. Right now it's only 25 slots...
  2. M

    Gateway 2000 NS-8000 Server

    Well I bought EDO ECC Ram off eBay. It even says EDO-64MB-ECC and is 60NS. I believe I tried SD, but I'm not sure what the deal is. The one notch in the middle goes in fine, but the notch near the end is a little off on the one on the motherboard.
  3. M

    Gateway 2000 NS-8000 Server

    Anyone?
  4. M

    Gateway 2000 NS-8000 Server

    Anyone got any ideas?
  5. M

    Gateway 2000 NS-8000 Server

    Ok, I got my RAM, 4x64MB ECC 168pin 60NS EDO RAM, and it still doesn't fit. The little notch closest to the end is just a few centimeters off again. Any ideas?
  6. M

    Gateway 2000 NS-8000 Server

    BTW, if I use dual P2 233 Mhz processors, and 256MBs of RAM with sufficient hard drive space, this thing should beable to run Windows Server 2003 right?
  7. M

    Gateway 2000 NS-8000 Server

    I can't seem to find the S/N on this thing anywheres. I mean theres 2 stickers with numbers on the rear of the case, but doesn't say Serial Number... I was on Ebay on found 168pin EDO ECC Ram, 4x64MB sticks 60NS. Should work, hopefully I will win it, no other bidders yet, 2 hours left... Also I...
  8. M

    Gateway 2000 NS-8000 Server

    Just got one of these from my mom's work, but there is no RAM. I googled for a little bit, went to the gateway support site, and said it needs 72bit 60ns ram. But I have some EDO ram laying around, and they definately do not fit this board. The DIMM slots have 2 notches, on near the end and one...
  9. M

    A few new network setup questions

    sounds sweet, just the way i like it, also, if i connect the computers to the switch, with the switch connected to the router, will the computers connected to the switch still get NAT and all? Thats also one of my major concerns. Since our DSL ISP only gives us to email accounts, that only means...
  10. M

    A few new network setup questions

    but they usually dont come with 2 WAN/ uplink ports? so i would connect my switch to my router using just a regular computer port?
  11. M

    A few new network setup questions

    On the setting up a Home Giga network, I dont understand option 1 a whole lot, the one that looks like what I am looking to do is option one. I think is what its saying purchase a regular router, and a gigabit switch, connect the switch to the uplink port on the router, then connect the all the...
  12. M

    A few new network setup questions

    I am moving soon, and I plan on building a new and better network. I am connected through DSL, probably 256k/128k. I am planning on building a gigabit network btw. I am looking for a router, one that has NAT software specifically since switches doesn't have that. But I am also looking for...
  13. M

    Can't get processor off HSF

    looks like everything went well, thanks a ton!!!
  14. M

    Can't get processor off HSF

    well got her off using rbV5's method, heated it with bowdryer for about 2-3 min, pushed on it a bit with the screwdriver, now i gotta put on some new TG, and cross your fingers,hopefully i didnt screw it up so it will run just fine =D
  15. M

    Can't get processor off HSF

    lol that might be a good idea... and whats finesse? lol
  16. M

    Can't get processor off HSF

    well just tried that, and it didnt budge....
  17. M

    Can't get processor off HSF

    The processor came off with the HSF, I had done this to another computer before, by the processor came off a lot easier, and with the nail polish, do i just get a q-tip and rub it where some of the TG near the processor is??
  18. M

    Can't get processor off HSF

    So I checked to make sure that the processor was a 478 pin, and it was, so I am trying to put it back in, but Gateway has pretty much used glue as Thermal Grease, and can't get the processor off of the HSF to put the processor back in the socket... any suggestions on how to?