Recent content by Yoshi64

Thanks for the tip, I will try that when I get home!

Hi, My CMOS-battery seems to be dead, since the BIOS resets everytime the power is turned off. However I have a problem replacing the old battery with a new one, since I can't seem to figure out how to remove the old one! I have uploaded some pictures here. If anyone has any tips, please...

I have a Belkin 54 mbit wireless router, which generally works perfectly with my Acer laptop (built-in WLAN). However when the computer has been in sleep mode (which turns the WLAN off), it sometimes take 20-30 minutes before I get a new IP-adress from the router. This can be really annoying, so...

Where can I download coolbits? It is a registry-hack, right? I would like an app that can overclock the card when I run certain games, and keep it at stock otherwise.. Is that possible?

Just replaced my Radeon 9800 with a GF 7600GT, and need some tips for good overclocking programs for new Nvidia cards...

I have a A64 3500+, and was wondering if the max temp is about the same on my A64 as for the opterons? Right now I'm running it in: CPU: 10x250 = 2500 RAM: 5/6 * 250 = 208 HTT: 4x250=1000 I have the retail cooler and stock voltage (1.40V). I get 44-45C during Prime95 Torture test...

Hmm, I seem to have gotten quite a good sample. Running 10x250 now, with 5/6 memory divider and 4 HTT multiplier, thus memory @ 208 Mhz and HTT @ 1000 Mhz. 1.40 V. Running Prime95 torture test "blend", and been stable for about 1.5 hours now. The CPU temp max out at 45C. Is this too high...

Well, I think 2640 will be a bit too high for my stock cooler and average ventilated case (2 fans in, 2 out, all low rpm). But it would be nice :)

Should I lower the HT-multiplier from 5 to 4 if I run 10x240? Is it ok to have my SATA HDD connected to port 1 ? dwcal: Thanks for the tip, I will try it!

Hi, I need some help overclocking my system. My cpu runs att 2200 Mhz (11x200) default, and my goal it to get it up to 2400, which is 11x218. I guess/hope that my Kingston value PC3200 can run @ ~440 mhz with slow timings, so I hope to keep a 1:1 FSB:RAM ratio. My problem is that I...

The weird thing was that I never had this problem on my old Abit AN7 (Nforce 2 Ultra 400). I tried increasing the rpm to the limit I accept (~2000 rpm) noise wise, but that wasn't enough to get it started. Zepper: I have the ASUS Q-Fan disabled, so it shouldn't be interfering (sp?)

I have a Enermax 80mm chassis-fan, where you can control the fan-rpm with a little nob that you turn. When I connected this fan to my new mainboard, an ASUS A8N-E, it didn't start. I connected it to the CHA1_FAN-header, which is the one closes to the intake fans in the front. The weird...

Just got a A64 3500+ retail, which runs at 39-40 degrees C under max load. Was thinking of bumping it up to 2.4 Ghz. But I was wondering if you get a better cooler with the 4000+? Seems my cooler is quite good, because I don't think 31-34 C idle and up to 40 C max load is that high...

Hmm, ok. Didn't know that hehe

Just got a A64 3500+ on a ASUS A8N-E (NForce 4 Ultra). So I installed windows XP SP2 on my primary drive (200 Gb Maxtor SATA), and now I have in the right corner of Windows the "safe removal of hardware"-icon (direct translation from swedish hehe). The one you get when you plug in an USB device...