Recent content by rathsach

  1. R

    Cisco Call Manager

    You'll have to have only one dhcp server pr. subnet if you want to control it as you wish.. I don't know if you can use it for anything, but you can block bootp packets (dhcp requests) in a Cisco access-list.. Maybe that's useful to you..
  2. R

    Free download of Microsoft "Understanding IPv6" e-book

    Nice find.. Thank you..
  3. R

    regarding Inter VLAN Routing

    If you want to route between them, just think of each switch as a router, and each vlan configured as a network interface. Remember to create both the vlan and the vlan interface. Enable IP Routing on each switch and pick a routing protocol..
  4. R

    Weirdness on a 4500 with a bad default gateway

    I kinda sounds to me like you may have replaced the backup SUP once before and then not having had the switch rebooted since.. So the sups had different configs loaded, or maybe in ROMON.. I've tried something similar with 2 brand new SUP's to be installed. One came with Hybrid IOS, and the...
  5. R

    Any CCIE's?

    QFT!.. Exactly how I feel... CCNP is the place to be if you want a diverse day.. CCIE would mainly be for bragging rights from where I am.. Before I got to where I am, I was definately aiming for CCIE because of the promised pay and the ability to pick and choose jobs.. But really, I get a nice...
  6. R

    Any CCIE's?

    CCNP here personally.. Not really aiming for the CCIE yet.. Maybe in a few years.. I have plenty of interesting assignments, and the CCIE's I know work like horses. 60-70 hour weeks are the norm for them all.. They do make a bit more than I do, but not enough to cover their extended workweek.. I...
  7. R

    3750 switch for intervlan communication?

    I've always failed to see the big advantage from 3750 gigabit switch stacking.. The cost is SO close to a 4506 chassis solution, that I don't think it makes sense going for a stack.. The stacking on the 3750 100mbit switches are a good cheap high port density access layer solution.. Gigabit...
  8. R

    F5 Load Balancers

    It's not that difficult actually.. You create the webservers as nodes, assign the nodes to a pool, and tells the F5 how to loadbalance (round robin etc).. When you get on the webinterface, and you list your resource (nodes, pools, etc), just start from the bottom one and work upwards.. It'll...
  9. R

    Taking Cisco Classes...

    I'd take a 1812w ISR router or a ASA5505 of you're more security oriented..
  10. R

    vpn connection drops out

    Which VPN product are we talking about here? Cisco VPN Client?
  11. R

    Help with Cisco PIX 506e Firewall Access Rule and NAT config

    Is it running Pix 7 or newer? You could try to connect via the ASDM and do a packet trace, see what it says.. Well spotted with the http server.. I'd try to disable that just in case that's what's making it all FUBAR..
  12. R

    Help with Cisco PIX 506e Firewall Access Rule and NAT config

    That's a bit odd.. Looks ok to me.. Try to remove fixup on http and see if that doesn't help.. It should ofcourse work with Fixup running, but try it anyway.. Any reason why you don't use the service group you made any more?
  13. R

    Need some help

    Why on earth would you want to use so many addresses for that? I just checked out your drawing again and saw that the bottom router was connected to another side of the top-right one.. Yesterday I saw it as a 3 way cross.. You'll have to tell me exactly what you need this to do? If it's...
  14. R

    Need some help

    Just pick a small unused subnet of RFC1918 addresses and assign an address to each router from those.. Then you're good to go.. With 3 addresses a /29 subnet is advisable..
  15. R

    One network, two internet connections?

    We need to know if the router you have forwards dhcp requests, and that campus has some form of control so each router can only have 1 ip. If this is not the case, then you can just put up a switch behind one of the routers and connect the pc's to that.. If not, then setup a router behind...