Recent content by meffie

  1. M

    Question about my cooling Setup

    NZXT Phantom 820 Case, i5 4690, Asus Maximus VII Hero, GTX 780, 256GbSSD, 2 TB WD Black, Gskill ram, Corsair H105i Radiator. This is my fan setup. Top: 2 200mm INTAKE (top of case) Top: H105i Radiator (in between) Push/Pull Setup Top: 2 140mm INTAKE (under radiator) Front: 200mm...
  2. M

    Yah I know....New Rig

    Thanks :P I'm digging her.
  3. M

    Yah I know....New Rig

    $1263.87 Shipped Case: Antec DF-85 CPU: Intel i5 2500K Sandy Bridge MB: Gigabyte GA-P67A Ram: GSkill Ripjaw 8gb GPU: MSI GTX 560 Ti PS: XFX 650W 80+ Bronze CPU Fan: Cooler Master 212+ SSD: Corsair 60Gb SSD Data: Samsung Spinpoint F3 1Tb Dvd: LG Burner Thermal...
  4. M

    Yah I know....New Rig

    Ok just got done with it. My HD Xfer rate is now a 7.6 on Windows Experience. Up .3 points. Sweet! Core's also only hit a max of 40Cel during the tests. I'm not sure how intensive the tests are, but I think that would be a good benchmark to say everythings running cool eh? Thanks again
  5. M

    Yah I know....New Rig

    Ok I'll get that changed and report back. Thanks so much again. You guys are life savers
  6. M

    Yah I know....New Rig

    Ok PCH Sata in the bios is set to IDE not AHCI. Can I simply change that in bios or do I need to do something else? Also should either of these HD's be hooked to the Sata 3 ports on the MB? Currently they're both hooked into Sata 2 ports. That's one place I'm not clear on. Just didn't know...
  7. M

    Yah I know....New Rig

    I ended up using this board not the msi if that helps any. I'll look in bios when I get home and see what I can see there
  8. M

    Yah I know....New Rig

    ATA Channel 0 ATA Channel 0 ATA Channel 1 ATA Channel 1 Intel(R) 6 Series/C200 Series Chipset Family 2 port Serial ATA Storage Controller - 1C08 Intel(R) 6 Series/C200 Series Chipset Family 4 port Serial ATA Storage Controller - 1C08 That's what I have under IDEA ATA/ATAPI controllers in...
  9. M

    Yah I know....New Rig

    Yah I got disk management setup for the 2nd HD np, I was refering to switching from Sata to AHCI. How to do that and what benefits it had. I already assembled the comp and it's up and running, but thanks for the input :)
  10. M

    Yah I know....New Rig

    Say What? lol. Can you explain how to do that in detail and what pro's/con's it has? Got it detected, format'd and assigned, thanks!
  11. M

    Yah I know....New Rig

    Using Aida 64 it says the Cpu is @ 20Cel, and each core is up to 30Cel at an idle. On a side note, windows is not detecting the data drive. It shows up in bios though. Wonder if I need to set the jumpers to slave, although the cheap drive that was recommended didn't come with a jumper :/...
  12. M

    Yah I know....New Rig

    All up and running. 7.3 Windows Experience. The SSD is the low mark apparently. 7.5 Processor 7.8 Ram 7.8 Graphics 7.8 Gaming Graphics 7.3 Primary HD That decent?
  13. M

    Yah I know....New Rig

    Sweet ty
  14. M

    Yah I know....New Rig

    One other quick question. The heatsink itself on the 212+ once fully installed moves ever so slighty rotationaly. The mounting screws on the "spider" attachment are fully seated. Is this normal?
  15. M

    Yah I know....New Rig

    10-4 thanks, I figured as such, but if not I was about to get pissed! :thumbsup: