Recent content by G.Robert

On several occasions now when the system is first started up, there will be no display on the monitor. There are no extra beeps from the system, just the normal single one and it seems like bootup is happening normally, as indicated by the hdd led. There is just no display of it on the monitor...

On several occasions now when the system is first started up, there will be no display on the monitor. There are no extra beeps from the system, just the normal single one and it seems like bootup is happening normally, as indicated by the hdd led. There is just no display of it on the monitor...

On several occasions now when the system is first started up, there will be no display on the monitor. There are no extra beeps from the system, just the normal single one and it seems like bootup is happening normally, as indicated by the hdd led. There is just no display of it on the monitor...

So if I understand correctly, I just need to go into the control panel-->network-->configuration tab-->highlight tcp/ip for the nic-->properties-->ip address tab and asign it 192.168.0.1? Do I need to do anything to the subnet mask setting? Will I need to undo this next week when I get the...

FUBAR- When I get connected to cable modem service next week would that fix the problem? How do I set the ip info statically to fix the bootup speed problem?

I went ahead and reinstalled Win98se, the latest Intel Chipset Utility and then the Intel Ultra ATA instead of the Application Accelerator and everything seems ok, sort of....... While the problem I described in my initial post seems resolved by the above action, something new has popped up...

I went ahead and reinstalled Win98se, the latest Intel Chipset Utility and then the Intel Ultra ATA instead of the Application Accelerator and everything seems ok, sort of....... While the problem I described in my initial post seems resolved by the above action, something new has popped up...

Hi all- I finally got the rig together and now have a few questions about it. I installed the usb 2 bracket and attached it to the headers on the P4B266 and installed the driver for it. When I look in device manager under Universal Serial Bus Controllers this is what I see: ---Asustek USB...

I just set up my rig and wanted to know what memory settings are good for this combo? I am running a stick of Crucial 2100. Also, there is a setting "sdram idle timer" with the following choices: infinite,0t,8t,16t, and 64t. Which of these settings are best. I am using the 1005 bios. Thanks

I just set up my rig and wanted to know what memory settings are good for this combo? I am running a stick of Crucial 2100. Also, there is a setting "sdram idle timer" with the following choices: infinite,0t,8t,16t, and 64t. Which of these settings are best. I am using the 1005 bios. Thanks

I am installing the P4 Alpha 8942 right now on an Asus P4B266/ Intel 1.6A and have had a difficult time of it. Is it normal for the motherboard to look a little bowed around the area where the Alpha is installed? When I look down the edge of the P4B266 it looks a little bowed where the Alpha is...

Turns out it was the memory. I remembered I had a stick of Crucial ddr 2100 here for a rig I'm gonna build so I slapped it in there and it booted right up. I double checked the Corsair and put it back in and it failed to boot again, so it looks like the Corsair crapped out on me. What memory...

Turns out it was the memory. I remembered I had a stick of Crucial ddr 2100 here for a rig I'm gonna build so I slapped it in there and it booted right up. I double checked the Corsair and put it back in and it failed to boot again, so it looks like the Corsair crapped out on me. What memory...

Jen- I have had the system running at 1450 since July 10x145fsb.

Canadian- All of the fans spin up when I turn power on: case, cpu hsf, vid card, everything. What do I put the mobo on in order to test as you suggest? Just put in the cpu, memory, and vid card and disconnect all of the drives, etc...?