Recent content by enclavesaga

  1. E

    HELP with ITune mess up!!!

    okay, am not going to bash this worthless piece of shxt program, i need some serious help. I've recently checked some wrong options in Itune, let it reorganized my music folder (over 30GBs), and of course it messed it up fubar. I've sorted out my folder tree by music genre, and then album, which...
  2. E

    ATI 3870 with ASUS P5W Deluxe

    ain't that obvious?
  3. E

    Gigabyte ds3 undervolted? can't shut down

    Just got a new DS3, rev2.0, for some reason my ArcticCooling freezer7 Pro fan is not spinning(it jerks on and off every other second)usually needs to finger it to jump start and keep it spnning, even when it's spinning, it's very slow, RPM is around 300. I wonder if this a under-voltage problem...
  4. E

    How to know if my video card supports 1680 x 1050

    nope, apparently your card is not dual head, go grab a cheap Matrox G400 or something.
  5. E

    How to know if my video card supports 1680 x 1050

    Holy Mary mother of God, where have u been for the past 6 years. Your Gf card is as old as your monitor I assume... It's a Nvida MX400 as i remember, perhaps even on a PCI bus, back to the golden age of 2000... anyway, it can go up to 2000x1500, you probably don't have the up to dated...
  6. E

    ATI, AMD roadmap leaked.

    sorry, the RD600 refers to the ATI chipset for motherboard, ATI graphic chip will of course continue to work on board using Intel cpu, but AMD will make sure there is some bottleneck issue. The info was leaked by AMD oversee stuff, probably in South America, doubt if there's any english...
  7. E

    ATI, AMD roadmap leaked.

    http://www.chilehardware.com/articulo.php?sid=1631&mode=thread&order=0&thold=0 Brief info: R600 will be build for PCIE2.0, 521bit memory bus, DDR4, 2ghz, DX10.b(theoretically 40% faster than the 8800GTX, need a PCIE2.0 board to fully take this advantage), same time released will be the AMD...
  8. E

    Help with setting up Intel Matrix

    After reading 'entering the matrx', i was inspired to do the following: I've recently acquired a Baraccuda 7200.9 500GB, with 4X125GB platters. My question is, how do i slice the harddrive using matrix, so that I can arrange 3-5GB out of each platter, making sure they are all sliced from the...
  9. E

    Dell

    Chances are, not supported. What's your motherboard chip model? anything prior 945 won't run C2D, you have a HT p4 chip, the MB shipped with it is most likely older than the 945. And Dell PSU has speical connectors to their MB of choice, so a after market PSU might not work, I had a Dell8300...
  10. E

    System can't detect IDE device after stand-by

    Got a strange problem, everytime I recover from stand-by, my IDE harddrive and DVD Rom seem to disappear, had to reboot the computer to gain access. My motherboard is the Asus P5wDH, SATA mainboot, AHCI enabled but set to basic, ACIP support enabled, ACPI compliant. Any fix?
  11. E

    Klipsch Ultra 5.1 users, urgent help needed(low volum)

    Okay, but here's what a Klipsch guy argued: quote "The controllers for both the 5.1 THX and the Ultra run on a logarithmic scale. This means that if your system's volume is maxed and the control pod is at 80, you are at full volume. If system is maxed and control pod is at 70, then you are...
  12. E

    Klipsch Ultra 5.1 users, urgent help needed(low volum)

    ya, i paid and picked up in store.
  13. E

    Klipsch Ultra 5.1 users, urgent help needed(low volum)

    Nope, I made sure the polarity is correct. I also tried other sats(the paradigm Cinema for example) and different inputs, Ipod, laptop, Dvdplayer..etc) I even cleaned my ear with wax removal :D ... the volum just doesn't crank up. The system is totally mute when the number in the...