Recent content by Ejhocky313

  1. E

    Continous Beeping

    Bought a cheap stick of generic RAM, it posted...so this week I will get some good corsair, and be back to things in no time. Thanks Again...
  2. E

    Continous Beeping

    I put a new motherboard in....same thing, so I guess rules out the motherboard, although I will be keeping the new motherboard. I am going to try to get my hands on some other RAM and go from there... Thanks to all for your help.
  3. E

    Continous Beeping

    perhaps, but...It was never technically overclocked. and to further this I bought a new Power Supply, and it is still doing the same thing....the next thing I will try I guess is a new motherboard...
  4. E

    Continous Beeping

    How could the CPU have been damaged? wouldn't it just not start up, I mean it's not like I had some outrageous vCore set.
  5. E

    *** Official Gigabyte P965-DS3 Thread ***

    I posted in this in the help section, but maybe those who have the same Motherboard me can shed some light... Last night I was trying to do a little over clocking on the computer and I ran into a couple of snags on the way. It was all fine and dandy though because on my Gigabyte motherboard...
  6. E

    Continous Beeping

    Last night I was trying to do a little over clocking on the computer and I ran into a couple of snags on the way. It was all fine and dandy though because on my Gigabyte motherboard, if it doesn't start up right the first couple tries it will reset the computer BIOS. heres where the problem...
  7. E

    Netgear ADSL+ Router with Cable Modem

    I was given the Netgear ADSL+ DG834G Router as a gift, and I havn't used it yet, as I move from my wired router to wireless. My question is if I have a cable modem (Charter) can I use this router or will I run into snags/incompatability. Thanks for the advice, if it doesn't work I will try...
  8. E

    *** Official Gigabyte P965-DS3 Thread ***

    Same results here, changing the PCIe frequency yeilds no results whatsoever...I will remain (semi-happy) at my overclocked 2.7 GHz state until there is possibly something else to try. I am not getting anywhere and I have tried everything.
  9. E

    *** Official Gigabyte P965-DS3 Thread ***

    Well, Following that guide I have ran into many problems as well...For some reason everytime try to get to 3.0 Ghz with my E6600 I can't post and it will restart the computer and reset it the previous BIOS setting. should I need to go more than +.01 on the FSB, MCH, and PCIe? I Have the...
  10. E

    *** Official Gigabyte P965-DS3 Thread ***

    Hello all! I just recieved this board on friday and installed everything without a hiccup (specs are in my profile sig) This if my first intel build since the Pentium 2, and I was writing this to see if someone could point me in a direction of how to overclock it. I did a few searches, but...
  11. E

    VISTA "Limited Connectivity" for 10-20 minutes from start up

    Well, a little help from the anandtech boards pays off again, that driver seemed to fix the annoying promblem. Thanks!
  12. E

    VISTA "Limited Connectivity" for 10-20 minutes from start up

    I got the latest Firmware for the Router... The Asrock board is a ULI chip, so yes indeed... I will try these when I get home, and report back thank you Eric
  13. E

    Microsoft Vista+Linksys WRT54G V.2=No internet

    What is the DD-WRT firmware? is it for the router? Thank You!
  14. E

    VISTA "Limited Connectivity" for 10-20 minutes from start up

    Hey that's the same promblem I am having!!! I Posted something about it in the Networking section: http://forums.anandtech.com/messageview.aspx?catid=36&threadid=2004178 Anyone figure out how to fix this, it's annoying... Do I need a new Router, or a PCI NIC card?
  15. E

    Microsoft Vista+Linksys WRT54G V.2=No internet

    Ok, this is the first time I have posted in the networking section, and I'm hoping this is the right place for my question. Here is what is going on: My router (Linksys WRT54G V.2) has worked flawlessly since I bought it a few years ago, all up until yesterday, when I made the move to windows...