Recent content by Doctahg

  1. D

    ANyone working with 12X or more with a 9650?

    ANyone Oc-ing with a 12X multi..or more! lol..Just wondered. Am running my 9650 at 11 X 333 with good temps and perfect stability. Wondered what 12X would bring and if so, what voltages you used. Thanks,'Doc
  2. D

    Anandtech Enzotech Ultra-X Review

    Well AGAIN...Anad's and my reviews vary...the Enzo is much better than the TR 120 Extreme....oh well. I'm going to lap the 120 Ext and see what happens.
  3. D

    Copper Heatsink on the Rocks

    You can build a heatsink but you can't focus a camera! sheeesh!!! LOL
  4. D

    Overclocking advice needed.

    The outside fan will do nothing to cool the processor.
  5. D

    My ENZOTECH ULTRA X performance so far

    If you have room and can reach then you can screw them in, but there are a couple that I could only screw down form the side, with my fingers between the heatpipes....
  6. D

    Finally got the Enzotech Ultra-X

    You can put the Enzotech in any of the 4 ways which will fit. I looked at your case, and if you flip it over it looks just like any other case, so I don't understand why it won't fit?
  7. D

    Some help needed with my OC please

    I swapped out the TR for the enzotech....I am not sure how to get 1-1 ratio with the Ram. Right now I lowered my Overclock to 3487, 1550X9. I don't need to push it although I had no major problems at 3.6... I have the cpu at 1.325...I lowered it from 1.35 when I lowered the FSB by 50 from...
  8. D

    My ENZOTECH ULTRA X performance so far

    I in no way shape or form could install it with the mobo half out of the case. I got the backplate in fine but could not screw the screws down at all. I took the plastic off the TR glue pad and it was fused to the mobo, so i need another for the spacing/cushion.
  9. D

    My ENZOTECH ULTRA X performance so far

    I in no way shape or form could install it with the mobo half out of the case. I got the backplate in fine but could not screw the screws down at all. I took the plastic off the TR glue pad and it was fused to the mobo, so i need another for the spacing/cushion.
  10. D

    My ENZOTECH ULTRA X performance so far

    I did ..the one I have is the RMA. At this point I'll try lapping...$50 experiment. If I do a good job, it may cool better than the Enzo, if not I'll be ready to lap the 6600! lol The RMA'e Xtreme did cool much better than the first one, but not near to the review. But, I think I wrote in...
  11. D

    My ENZOTECH ULTRA X performance so far

    Got rid of my QX6700...they need H2O and I really don't have time now...when the next CPU's come out! ANYWAYS....Using an E6600. Installed my RMA board last night and put the Enzo on it...out of the case an absolute must. My room is 71-72F, but my computer is under my desk near the AC vent...
  12. D

    Some help needed with my OC please

    Well I just got it up to 3600. CPU at 1.35, cpuz says1.304(I guess you add .03 to that so 1.334)... 45 minutes of ORTHOS doing small stress the cpu stuff..FFT's? lol No problems there. My idle, doing this, is at 37-39 ish. The high for Orthos was 59, but ran more at 57-58. My startup temps...
  13. D

    Some help needed with my OC please

    I raised the cpu volts a bit to 1.3125. And the FSB is 1550. I'm now at 3492. I ran Orthos for an it was no higher than 54 on both cores. I tried 8X to see if I could get the FSB higher and how that worked. Don't ubderstand the safe mode thing...
  14. D

    Some help needed with my OC please

    -------------------------------------------------------------------------------- Just wanted to see what you people thought of where I am and if my volts are OK...and where to go from here. I'm on air, so that's limited. Room is 28+ ambient. I am idling, right now writing this at 37-37. I ran...
  15. D

    Should have quit messin...now the Computer

    The TIM was perfect, the mount was as well. Unfortuately the high spot prevented it from hitting. It's not the processor. The stock sink and the cpu had a nice thin even coat when I removed it.... <<<<Just don't overheat anything when doing this!>>>>> The Ultra Ex is taking care of this...