I just picked up one of these drives. Has not gotten here yet and I am anticipating it's arrival. From the reveiws I read it's a good drive and has the self healing feature.
http://www.newegg.com/Product/Produc...-087-_-Product
Hi,
I just put one of these in my box. It is the CAYC stepping and from what I have read this is a good stepping for unlocking. Unfortunately my board has the 700 SB and not the 710 or 750 so unlocking the cores is out. It runs stablle 3.12Ghz, stock voltage. All I did was drop the multiplier...
My take
Pick up this board
GIGABYTE GA-MA78G-DS3HP $85
Your memory $45
Opty 1210HE $83 if you shop around
HD4830 $74
For under $300 you get a board that is AM3 compatible and the opty will OC to 3G+. Mine is stable at 3.0 (1200mhz OC). It has almost as much cache as the Kuma and is...
I have some original PQI Turbo memory, TCCD. It run flawlessly at 3-4-4-8-1T at 275 FSB 1:1 2.7V. Running it on a 9NPA+ Ultra board. Have tried to squeeze the timings and the bandwidth is best at these settings.
tubar,
What is up? There is a lot of skepticism in regards to your creditbility as you have quite a few AT'ers pissed off right now. To say the least you have some balls! Please refer to this link
tubars FS Post
"that I have a bit of cash laying around" is an understatement!
"Also...
Standard PCI cards will wok in the slots as long as they are keyed on both ends. I am running in jumper free mode and have the following cards installed
Slot 1 - D-Link network card
Slot 2 - USB 2.0 Card
Slot 3 - Empty...........Audigy will go here
Slot 4 - Advansys 3940 U2W SCSI
Slot 5 - AMI...
What is the best driver for this card? I have a VisionTek GF3 and am using the drivers off the disk that came with it. Also what is the highest AGP Bus speed optainable with this card?
LMK
I have a Hot Rod 100 controller card that took some trial and error to get XP to load. XP ships with all of MS's digitally certified drivers so when I hit F6 and loaded the High Point drivers it hung when loading the OS. So I let XP load it own set of drivers for the card. High Point now has...
I have flashed my bios and am not able to get to the 166GSB to enable the 1/5 divider. I am using 1 256 mb stick of Crucial PC2100 DDR. Here's my setup and your advice is appreciated
1.333 Tbird Water Cooled
8K7A
256 mb Crucial PC2100 DDR
Radeon 64 mb DDR Vivo
SB Live
Zoom 56K Modem
LMK
Title says it all. I recently acquired the fore mentioned SCSI card and a Quantum Atlas V 10K drive with the adapter and 68 pin cable. The drive is a 160 LVD and I am using a 68 pin cable that is properly terminated (LVD). I need to know how to configure the card to achieve Ultra-2 SCSI transfer...
Follow o1die's advice and you should be fine applying the HSF. I just got a 1.333 AYHJA chip yesterday and installed it and was able to reach 1.6G stable. I am water cooling it and opted for 1554 as the speed to leave it at. I am also running a Epox 8K7A mobo.
Good Luck!
OEM chips definitely clock as good or better than reatil chips. I have never purchased a retail chip and have had very good results with OEM chips. What's nice is if you go to a local shop you can check out all the cores in a tray and choose accordingly.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.