Go Back   AnandTech Forums > Hardware and Technology > Motherboards

Forums
· Hardware and Technology
· CPUs and Overclocking
· Motherboards
· Video Cards and Graphics
· Memory and Storage
· Power Supplies
· Cases & Cooling
· SFF, Notebooks, Pre-Built/Barebones PCs
· Networking
· Peripherals
· General Hardware
· Highly Technical
· Computer Help
· Home Theater PCs
· Consumer Electronics
· Digital and Video Cameras
· Mobile Devices & Gadgets
· Audio/Video & Home Theater
· Software
· Software for Windows
· All Things Apple
· *nix Software
· Operating Systems
· Programming
· PC Gaming
· Console Gaming
· Distributed Computing
· Security
· Social
· Off Topic
· Politics and News
· Discussion Club
· Love and Relationships
· The Garage
· Health and Fitness
· Home and Garden
· Merchandise and Shopping
· For Sale/Trade
· Hot Deals with Free Stuff/Contests
· Black Friday 2014
· Forum Issues
· Technical Forum Issues
· Personal Forum Issues
· Suggestion Box
· Moderator Resources
· Moderator Discussions
   

Reply
 
Thread Tools
Old 11-18-2012, 08:33 AM   #1
Xenphor
Member
 
Join Date: Sep 2007
Posts: 121
Default Missing one stand off for MSI z77a-g43 MB.

Well reading on the internet some people say it's okay others say you need all stand offs. The problem I had is that one stand off from my previous motherboard was stuck, attached to a screw. I could not for the life of me get the stand off to come off so I just decided to go without one for my new MB (didn't have any extra).

My setup is this:
0 0 0

0 0 x

0 0 0

the x is where the missing stand off is. I have already installed everything else so I don't plan on flexing the board with any additional components at this time. At the moment all I have installed is one videocard in the pcie 3.0 slot and the CPU.

Last edited by Xenphor; 11-18-2012 at 08:36 AM.
Xenphor is offline   Reply With Quote
Old 11-19-2012, 06:56 PM   #2
Ksyder
Golden Member
 
Join Date: Feb 2006
Posts: 1,798
Default

I wouldn't worry about it. What you want to avoid is a standoff in a place where it is not supposed to be, such as a place that can short out circuitry on the rear of the motherboard.
Ksyder is offline   Reply With Quote
Old 11-19-2012, 10:48 PM   #3
Xenphor
Member
 
Join Date: Sep 2007
Posts: 121
Default

Well fortunately I was able to get some more stand offs and have corrected the issue.

But I have another question. The CPU 8pin power connector is in the top left portion of the motherboard and there is literally no room there, especially since I have a fan exhausting at the top. What I've had to do is run the 8pin adapter from my power supply over top of everything else in my case and then tie it up at the top. The rest of the cable then goes left to where the 8pin power socket is. In this position, the cable is unfortunately in between the top left portion of my motherbaord (with cpu heatsink+fan blowing towards the top) and an exhaust fan (also at the top).

So I'm basically wondering if this is a decent long term solution? If my case had some more room at the top I would just run the cable from the back of the board to the top, bypassing the need to ziptie the cable off and route it between both fans. It would also be nice not to have a cable extending from the bottom of the case all the way to the top which I'm guessing might impede airflow.

My case is an NZXT source 210

Last edited by Xenphor; 11-19-2012 at 10:52 PM.
Xenphor is offline   Reply With Quote
Old 11-19-2012, 11:00 PM   #4
infoiltrator
Senior Member
 
infoiltrator's Avatar
 
Join Date: Feb 2011
Location: Waterbury, CT
Posts: 695
Default

There are cable extenders that should allow you to route the cable either behind the motherboard tray or at least out of the way.
http://www.amazon.com/CB-8P-8-Pin-Mo...ower+extention

http://www.amazon.com/StarTech-com-8...ower+extention

Or you can extend eisting wires.
__________________
Damn the cost, full build ahead! I wish.
infoiltrator is offline   Reply With Quote
Old 11-20-2012, 12:08 AM   #5
Xenphor
Member
 
Join Date: Sep 2007
Posts: 121
Default

I managed to make it fit by removing the fan that was there. Now I'm afraid I'm gunna strip the wires over time because it was a very tight fit, especially where the cable arches over the back of the motherboard and into those connectors.
Xenphor is offline   Reply With Quote
Old 12-04-2012, 01:06 PM   #6
JerryOneMillion
Junior Member
 
Join Date: Nov 2010
Location: Los Angeles
Posts: 14
Default

You could try something like this...

http://www.ebay.com/itm/8-Nylon-Moth...item519ed96c61
JerryOneMillion is offline   Reply With Quote
Old 12-05-2012, 01:05 AM   #7
GPz1100
Senior Member
 
Join Date: Jun 2001
Posts: 337
Default

Whether or not a stand off is present, it's always best to support areas such as the power connector, memory slots, or pcie slots. I've use nonconductive rubber feet before. Sometimes have to a few together to get the height needed.
__________________
Living reality in a dream

p8z77v-deluxe, 3770K @ 4.6, +.050V offset, LLC at high, xspc raystorm/ex360 WC
GPz1100 is offline   Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:51 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.